Maytag dryer F2E3 error code
F2E3 does not mean the same thing on every Maytag dryer. Our data shows 2 documented meanings, depending on which engineering platform the model is built on. Look up your model number to see the one that applies.
| Meaning | Appliance | Maytag models |
|---|---|---|
| Control programming error | Electric dryer, Gas dryer | 96 |
| Interface and control mismatch | Electric dryer, Gas dryer | 8 |
F2E3: Control programming error
- Brand
- Maytag
- Appliance
- Electric dryer, Gas dryer
- Code
- F2E3
- Documented meaning
- Control programming error
- Applies to
- 96 Maytag models on 2 platforms
- Can you keep using it?
- With caution
F2E3 on 2010 platforms means the main control's stored model programming was not loaded correctly.
What the dryer is detecting
The main control keeps model-specific settings in memory. When those settings are missing or not programmed correctly, the interface reports F2E3.
Causes listed for this condition
In the order the service documentation checks them. Documented causes come from the manufacturer's service documentation for these platforms; possible causes are based on how the system works; unconfirmed marks common assumptions that the documentation does not support.
- Documented Main control memory not programmed correctly for the model.
- Documented A user interface fault; the documentation's corrective step is the interface board.
Safe checks you can make
- Turn the dryer off at the breaker (or unplug it) for about one minute, restore power and start a new cycle to see whether the code comes back right away.
Further diagnosis requires opening the appliance. Beyond the owner checks, diagnosis involves removing panels, testing components and checking wiring. We describe what a technician investigates, not how to do it yourself.
What a technician checks
- Confirms the board part numbers match the model.
- Replaces the board identified by the service documentation for this code.
Typical repairs and cost
Depending on what diagnosis finds, this code can lead to one of these repairs:
| Repair | Typical range | Labor |
|---|---|---|
| Dryer main control board replacement | $280–$640 | Moderate |
| Dryer user interface / keypad replacement | $230–$510 | Light |
Typical total ranges for the Las Vegas area, parts and labor included. The final cost depends on diagnosis, the exact model, parts availability and whether other damage is found.
Can you keep using it?
Use with caution. If the dryer runs normally after a reset, use it with care; a persistent code means the controls are not configured correctly.
Maytag models documented with this code
- MGD3000BG
- MGD3000BW
- MGD3000CG
- MGD3000CW
- MGD3100DW
- MGD3500FW
- MGD4000BW
- MGD4000CW
- MGD4100DW
- MGD4200BG
- MGD4200BW
- MGD4200CG
- MGD4200CW
- MGD4300DC
- MGD4300DG
- MGD4300DW
And 80 more. Use the model lookup to check yours.
F2E3: Interface and control mismatch
- Brand
- Maytag
- Appliance
- Electric dryer, Gas dryer
- Code
- F2E3
- Documented meaning
- Interface and control mismatch
- Applies to
- 8 Maytag models on 4 platforms
- Can you keep using it?
- No — stop and have it checked
F2E3 on 2015-2016 platforms means the user interface and the main control carry different model settings, usually after a board was replaced with the wrong part.
What the dryer is detecting
The main control and the interface board compare model identification at start-up. A mismatch, typically from an incorrect replacement part, sets F2E3.
Causes listed for this condition
In the order the service documentation checks them. Documented causes come from the manufacturer's service documentation for these platforms; possible causes are based on how the system works; unconfirmed marks common assumptions that the documentation does not support.
- Documented A replacement user interface or main control with the wrong part number.
Safe checks you can make
- If a board was replaced recently, check that its part number matches the parts list for your exact model.
Further diagnosis requires opening the appliance. Beyond the owner checks, diagnosis involves removing panels, testing components and checking wiring. We describe what a technician investigates, not how to do it yourself.
What a technician checks
- Compares both board part numbers with the model's parts list and replaces the one that does not match.
Typical repairs and cost
Depending on what diagnosis finds, this code can lead to one of these repairs:
| Repair | Typical range | Labor |
|---|---|---|
| Dryer user interface / keypad replacement | $230–$510 | Light |
| Dryer main control board replacement | $280–$640 | Moderate |
Typical total ranges for the Las Vegas area, parts and labor included. The final cost depends on diagnosis, the exact model, parts availability and whether other damage is found.
Can you keep using it?
Stop using it until it is checked. Do not use the dryer until the correct board is installed.
Maytag models documented with this code
Related problems and codes
Other codes documented on the same Maytag platforms:
Repair or replace?
A fault code alone rarely justifies replacing a dryer. Most F2E3 repairs involve a single component once diagnosed. Replacement becomes worth considering when the unit is near the end of its typical 12–14-year life and the diagnosed repair is a major one. See the repair-or-replace guide.
Need F2E3 diagnosed in the Las Vegas area?
We repair Whirlpool, Maytag, KitchenAid, JennAir, Amana and other Whirlpool-family appliances in Las Vegas, Henderson, Summerlin and Boulder City. A model number helps but is never required to book.