Maytag YMEDB835DW Electric dryer
Troubleshooting, fault codes and repair information for the Maytag YMEDB835DW, organized around the engineering platform this electric dryer is built on.
- Brand
- Maytag
- Model
- YMEDB835DW
- Engineering revisions
- YMEDB835DW0, YMEDB835DW1, YMEDB835DW2, YMEDB835DW3, YMEDB835DW4
- Appliance
- Electric dryer
- Platform
- Electric dryer platform, documentation from about 2015
- Models on this platform
- 12 across Maytag, Whirlpool
- Documented fault codes
- 12 with explanations
- Service diagnostic mode
- Yes — a console-only test mode used by technicians to read stored codes and run component tests
- Service documentation
- Tech sheet (used by our technicians; not published)
Maytag YMEDB835DW error codes
These are the fault codes documented for the platform this model belongs to. A code describes a condition the control detected; it does not by itself identify a failed part. Select a code for causes, safe checks and repair context.
| Code | Meaning | Areas involved |
|---|---|---|
| F1E1 | Main control fault | Main control board, Wiring harness and connectors, Drive motor |
| F1E3 | Incorrect controller installed | Main control board, User interface / keypad board |
| F2E1 | Stuck button or interface problem | User interface / keypad board |
| F3E1 | Exhaust thermistor fault | Temperature sensor (thermistor), Wiring harness and connectors, Main control board |
| F3E2 | Moisture sensor fault | Moisture sensor bars, Wiring harness and connectors, Main control board |
| F3E3 | Inlet thermistor fault | Temperature sensor (thermistor), Wiring harness and connectors, Main control board |
| F4E1 | Heat circuit or connector problem | Heating element, Gas valve and coils, Igniter |
| F4E2 | Second heater circuit problem | Heating element, Wiring harness and connectors, Main control board |
| F4E3 | Restricted airflow | Exhaust vent duct, Blower wheel, Temperature sensor (thermistor) |
| F4E4 | L2 line voltage error | Wiring harness and connectors, Main control board |
| F6E2 | Communication error (control to interface) | Wiring harness and connectors, User interface / keypad board, Main control board |
| F6E3 | Communication error (control cannot hear interface) | Wiring harness and connectors, User interface / keypad board, Main control board |
Common dryer problems
Typical dryer repair costs
| Repair | Typical range | Labor |
|---|---|---|
| Dryer heating element replacement | $180–$400 | Moderate |
| Dryer thermal fuse and thermostat replacement | $180–$310 | Light |
| Dryer drive motor or blower wheel replacement | $250–$550 | Heavy |
| Dryer drum belt replacement | $180–$320 | Light |
| Dryer drum rollers, glides and idler pulley replacement | $190–$420 | Moderate |
| Dryer moisture sensor bar repair | $180–$310 | Light |
| Dryer door switch replacement | $180–$290 | Light |
| Dryer exhaust thermistor replacement | $180–$290 | Light |
| Dryer main control board replacement | $280–$640 | Moderate |
| Dryer user interface / keypad replacement | $230–$510 | Light |
Typical total ranges for the Las Vegas area, parts and labor included. The final cost depends on diagnosis, the exact model, parts availability and whether other damage is found.
Repair or replace?
Dryers typically last about 12–14 years. Service documentation for this platform dates from about 2015, so the oldest units built on it are now around 11 years old. The age printed in the serial number, the repair cost and the condition of the rest of the appliance decide it. Use the repair-or-replace guide.
Models built on the same platform
These models share this platform's service documentation, so fault codes and most diagnostic steps are the same.
- Whirlpool WED8000DW
- Whirlpool WED8500DC
- Whirlpool WED8500DR
- Whirlpool WED8500DW
- Whirlpool WED8510FW
- Whirlpool WED9000EW
- Whirlpool YWED8000DW
- Whirlpool YWED8500DC
- Whirlpool YWED8500DW
- Maytag YMEDB855DC
- Maytag YMEDB855DW
Need your Maytag YMEDB835DW repaired in the Las Vegas area?
We repair Whirlpool, Maytag, KitchenAid, JennAir, Amana and other Whirlpool-family appliances in Las Vegas, Henderson, Summerlin and Boulder City. A model number helps but is never required to book.