Whirlpool WGT4027HW Laundry center
Troubleshooting, fault codes and repair information for the Whirlpool WGT4027HW, organized around the engineering platform this laundry center is built on.
- Brand
- Whirlpool
- Model
- WGT4027HW
- Engineering revisions
- WGT4027HW, WGT4027HW0, WGT4027HW1, WGT4027HW2
- Appliance
- Laundry center
- Platform
- Laundry center platform, documentation from about 2013
- Models on this platform
- 11 across Maytag, Whirlpool
- Documented fault codes
- 20 with explanations
- Service diagnostic mode
- Yes — a console-only test mode used by technicians to read stored codes and run component tests
- Service documentation
- Tech sheet, service manual (used by our technicians; not published)
Whirlpool WGT4027HW error codes
These are the fault codes documented for the platform this model belongs to. A code describes a condition the control detected; it does not by itself identify a failed part. Select a code for causes, safe checks and repair context.
| Code | Meaning | Areas involved |
|---|---|---|
| F0E2 | Oversuds | Water-level pressure sensor and hose, Main control board |
| F0E4 | High water temperature in rinse | Water inlet valve, Temperature sensor (thermistor) |
| F0E5 | Off-balance load | Suspension rods, springs and dampers |
| F1E1 | Main control fault | Main control board |
| F1E2 | Motor control fault | Main control board, Drive motor, Wiring harness and connectors |
| F2E1 | Stuck key | User interface / keypad board |
| F2E3 | Switch mismatch | User interface / keypad board, Main control board |
| F3E1 | Pressure system fault | Water-level pressure sensor and hose, Main control board |
| F5E1 | Lid switch fault | Lid lock assembly, Main control board |
| F5E2 | Lid lock fault | Lid lock assembly, Main control board |
| F5E3 | Lid unlock fault | Lid lock assembly, Main control board |
| F5E4 | Lid not opened between cycles | Lid lock assembly |
| F7E1 | Basket speed fault | Drive motor, Shifter (shift actuator), Wiring harness and connectors |
| F7E5 | Shifter fault | Shifter (shift actuator), Wiring harness and connectors, Main control board |
| F7E6 | Motor fault | Drive motor, Wiring harness and connectors |
| F7E7 | Motor unable to reach target speed | Drive motor, Main control board |
| F8E1 | No fill / long fill | Water inlet valve, Water-level pressure sensor and hose |
| F8E3 | Overflow | Water inlet valve, Water-level pressure sensor and hose, Main control board |
| F8E5 | Hot and cold reversed | Water inlet valve |
| F9E1 | Long drain | Drain pump, Water-level pressure sensor and hose |
Common laundry center problems
- Not draining
Documented check order on this platform: Drain hose installation → Drain pump and pump inlet → Wiring and connectors → Main control board - Not spinning
Documented check order on this platform: Lid or door switch / lock → Drive belt → Wiring and connectors → Shifter → Drive or pump motor - Not heating
Documented check order on this platform: Power supply to the appliance - Not starting
Documented check order on this platform: Power supply to the appliance → User interface / keypad → Main control board → Lid or door switch / lock - Leaking
Documented check order on this platform: Water-level pressure sensing → Water inlet valve → Main control board
Typical laundry center repair costs
| Repair | Typical range | Labor |
|---|---|---|
| Laundry center drain pump replacement | $200–$440 | Moderate |
| Laundry center water inlet valve replacement | $180–$390 | Light |
| Laundry center lid lock / lid switch replacement | $190–$410 | Moderate |
| Laundry center washer suspension repair | $200–$460 | Moderate |
| Laundry center motor replacement | $280–$620 | Heavy |
| Laundry center belt replacement | $180–$360 | Moderate |
| Laundry center dryer heating element replacement | $200–$430 | Moderate |
| Laundry center thermal fuse and thermostat replacement | $180–$330 | Light |
| Laundry center dryer drum support repair | $210–$440 | Moderate |
| Laundry center dryer vent cleaning | $180–$350 | Light |
Typical total ranges for the Las Vegas area, parts and labor included. The final cost depends on diagnosis, the exact model, parts availability and whether other damage is found.
Repair or replace?
Laundry centers typically last about 10–13 years. Service documentation for this platform dates from about 2013, so the oldest units built on it are now around 13 years old. The age printed in the serial number, the repair cost and the condition of the rest of the appliance decide it. Use the repair-or-replace guide.
Models built on the same platform
These models share this platform's service documentation, so fault codes and most diagnostic steps are the same.
- Whirlpool WET4027EW
- Whirlpool WET4027HW
- Whirlpool WETLV27FW
- Whirlpool WETLV27HW
- Whirlpool WGT4027EW
- Whirlpool WGTLV27FW
- Whirlpool WGTLV27HW
- Whirlpool YWET4027EW
- Whirlpool YWET4027HW
- Maytag YMET3800XW
Need your Whirlpool WGT4027HW repaired in the Las Vegas area?
We repair Whirlpool, Maytag, KitchenAid, JennAir, Amana and other Whirlpool-family appliances in Las Vegas, Henderson, Summerlin and Boulder City. A model number helps but is never required to book.