Maytag MGD7000CG Gas dryer
Troubleshooting, fault codes and repair information for the Maytag MGD7000CG, organized around the engineering platform this gas dryer is built on.
- Brand
- Maytag
- Model
- MGD7000CG
- Engineering revisions
- MGD7000CG0
- Appliance
- Gas dryer
- Platform
- Gas dryer platform, documentation from about 2010
- Models on this platform
- 131 across Amana, Crosley, Maytag, Whirlpool
- Documented fault codes
- 19 with explanations
- Service diagnostic mode
- Yes — a console-only test mode used by technicians to read stored codes and run component tests
- Service documentation
- Tech sheet (used by our technicians; not published)
Maytag MGD7000CG error codes
These are the fault codes documented for the platform this model belongs to. A code describes a condition the control detected; it does not by itself identify a failed part. Select a code for causes, safe checks and repair context.
| Code | Meaning | Areas involved |
|---|---|---|
| F1E1 | Main control fault | Main control board, Wiring harness and connectors, Drive motor |
| F2E1 | Stuck button or interface problem | User interface / keypad board |
| F2E2 | User interface software error | User interface / keypad board, Wiring harness and connectors |
| F2E3 | Control programming error | Main control board, User interface / keypad board |
| F3E1 | Exhaust thermistor fault | Temperature sensor (thermistor), Wiring harness and connectors, Main control board |
| F3E2 | Exhaust thermistor shorted | Temperature sensor (thermistor), Wiring harness and connectors, Main control board |
| F3E3 | Inlet thermistor fault | Temperature sensor (thermistor), Wiring harness and connectors, Main control board |
| F3E4 | Inlet thermistor shorted | Temperature sensor (thermistor), Wiring harness and connectors, Main control board |
| F3E5 | Inlet and exhaust thermistors open | Wiring harness and connectors, Temperature sensor (thermistor), Main control board |
| F3E6 | Moisture sensor open | Moisture sensor bars, Wiring harness and connectors |
| F3E7 | Moisture sensor shorted | Moisture sensor bars, Wiring harness and connectors |
| F4E1 | Heat circuit or connector problem | Heating element, Gas valve and coils, Igniter |
| F4E3 | Restricted airflow | Exhaust vent duct, Blower wheel, Temperature sensor (thermistor) |
| F4E4 | L2 line voltage error | Wiring harness and connectors, Main control board |
| F6E1 | Communication error (control and interface) | Wiring harness and connectors, User interface / keypad board, Main control board |
| F6E2 | Communication error (control to interface) | Wiring harness and connectors, User interface / keypad board, Main control board |
| AF | Restricted airflow | Exhaust vent duct, Blower wheel |
| L2 | Low line voltage | Wiring harness and connectors, Main control board |
| PF | Power failure | Wiring harness and connectors |
Common dryer problems
Typical dryer repair costs
| Repair | Typical range | Labor |
|---|---|---|
| Dryer thermal fuse and thermostat replacement | $180–$310 | Light |
| Gas dryer valve coil or gas valve replacement | $180–$420 | Moderate |
| Gas dryer igniter and flame sensor replacement | $180–$370 | Light |
| Dryer drive motor or blower wheel replacement | $250–$550 | Heavy |
| Dryer drum belt replacement | $180–$320 | Light |
| Dryer drum rollers, glides and idler pulley replacement | $190–$420 | Moderate |
| Dryer moisture sensor bar repair | $180–$310 | Light |
| Dryer door switch replacement | $180–$290 | Light |
| Dryer exhaust thermistor replacement | $180–$290 | Light |
| Dryer main control board replacement | $280–$640 | Moderate |
Typical total ranges for the Las Vegas area, parts and labor included. The final cost depends on diagnosis, the exact model, parts availability and whether other damage is found.
Repair or replace?
Dryers typically last about 12–14 years. Service documentation for this platform dates from about 2010, so the oldest units built on it are now around 16 years old. The age printed in the serial number, the repair cost and the condition of the rest of the appliance decide it. Use the repair-or-replace guide.
Models built on the same platform
These models share this platform's service documentation, so fault codes and most diagnostic steps are the same.
- Whirlpool WGD70DUMMY
- Whirlpool WGD70HEBW
- Whirlpool WGD70HECW
- Whirlpool WGD71HEBW
- Whirlpool WGD71HEDW
- Whirlpool WGD72HEDW
- Whirlpool WGD7505FW
- Whirlpool WGD7540FW
- Whirlpool WGD7590FW
- Whirlpool WGD75HEFW
- Whirlpool WGD7740FW
- Whirlpool WGD77HEFW
- Whirlpool WGD80HEBC
- Whirlpool WGD80HEBW
- Whirlpool WGD80HECC
- Whirlpool WGD80HECW
- Whirlpool WGD81HEDC
- Whirlpool WGD81HEDW
- Whirlpool WGD83HEDCB
- Whirlpool WGD8540FW
- Whirlpool WGD85HEFC
- Whirlpool WGD85HEFW
- Whirlpool WGD86HEBC
- Whirlpool WGD86HEBW
- Whirlpool WGD86HECC
- Whirlpool WGD86HECR
- Whirlpool WGD86HECW
- Whirlpool WGD8740DC
- Whirlpool WGD8740DW
- Whirlpool WGD8740HEDC
Need your Maytag MGD7000CG repaired in the Las Vegas area?
We repair Whirlpool, Maytag, KitchenAid, JennAir, Amana and other Whirlpool-family appliances in Las Vegas, Henderson, Summerlin and Boulder City. A model number helps but is never required to book.