Whirlpool WFW5090JW Front-load washer
Troubleshooting, fault codes and repair information for the Whirlpool WFW5090JW, organized around the engineering platform this front-load washer is built on.
- Brand
- Whirlpool
- Model
- WFW5090JW
- Engineering revisions
- WFW5090JW0, WFW5090JW00, WFW5090JW1
- Appliance
- Front-load washer
- Platform
- Front-load washer platform, documentation from about 2016
- Models on this platform
- 4 across Whirlpool
- Documented fault codes
- 0 with explanations, 19 more listed
- Service diagnostic mode
- Yes — a console-only test mode used by technicians to read stored codes and run component tests
- Service documentation
- Tech sheet, service manual (used by our technicians; not published)
Whirlpool WFW5090JW error codes
These are the fault codes documented for the platform this model belongs to. A code describes a condition the control detected; it does not by itself identify a failed part. Select a code for causes, safe checks and repair context.
| Code | Meaning | Areas involved |
|---|---|---|
| F01 | No Water Detected Entering Washer Or Pressure Sensor Level Not Detected (explanation not yet published) | |
| F03 | Long Drain (explanation not yet published) | |
| F04 | Heating Time Too Long (explanation not yet published) | |
| F05 | Water Temperature Sensor Error (explanation not yet published) | |
| F06 | Blocked Drum/Motor Overload (explanation not yet published) | |
| F07 | Motor Control Internal Failure (explanation not yet published) | |
| F08 | Heater Failure (explanation not yet published) | |
| F10 | Drum Overload (Over-temperature) (explanation not yet published) | |
| F11 | Motor Control Internal Failure (explanation not yet published) | |
| F13 | ACU Failure On Door Lock Control Circuit (explanation not yet published) | |
| F18 | or Fod Suds (Foam) Detected During Wash Cycle (explanation not yet published) | |
| F20 | ACU Failure (Or Heater Failure) (explanation not yet published) | |
| F21 | User Interface Communication Error (explanation not yet published) | |
| F24 | Overflow Failure (explanation not yet published) | |
| F26 | Pump Driver Failure (explanation not yet published) | |
| F27 | Motor Phase Loss (explanation not yet published) | |
| F29 | Door Lock Failure (explanation not yet published) | |
| F34 | Maximum Spin Speed Not Reached (explanation not yet published) | |
| F60 | ACU Failure/Microprocessor Failure (explanation not yet published) |
Common washer problems
- Not draining
Documented check order on this platform: Drain hose installation → Drain pump and pump inlet → Wiring and connectors - Not spinning
Documented check order on this platform: Drain pump and pump inlet → Wiring and connectors → Drive or pump motor - Not filling
Documented check order on this platform: Inlet hose screens → Drain hose installation → Water inlet valve → Water-level pressure sensing - Leaking
Documented check order on this platform: Wiring and connectors → Drain hose installation → Load size or distribution → Dispenser → Exhaust vent restriction - Not starting
Documented check order on this platform: Power supply to the appliance → Wiring and connectors → User interface / keypad → Main control board - Shaking or noisy
Documented check order on this platform: Heating element → Inlet hose screens → Suspension → Exhaust vent restriction → Water-level pressure sensing - Door or lid locked
- Stops mid-cycle
Documented check order on this platform: Wiring and connectors → Drive or pump motor - Bad odor
Typical washer repair costs
| Repair | Typical range | Labor |
|---|---|---|
| Washer drain pump replacement | $180–$420 | Moderate |
| Washer water inlet valve replacement | $180–$360 | Light |
| Washer water-level pressure sensor repair | $180–$350 | Light |
| Front-load washer door lock replacement | $180–$400 | Moderate |
| Washer drive motor replacement | $300–$720 | Heavy |
| Washer motor control board replacement | $280–$600 | Moderate |
| Washer drive belt replacement | $180–$330 | Light |
| Washer suspension rods, springs or dampers replacement | $180–$440 | Moderate |
| Front-load washer tub bearing replacement | $550–$1,100 | Major |
| Front-load washer door boot seal replacement | $220–$510 | Moderate |
Typical total ranges for the Las Vegas area, parts and labor included. The final cost depends on diagnosis, the exact model, parts availability and whether other damage is found.
Repair or replace?
Washers typically last about 10–13 years. Service documentation for this platform dates from about 2016, so the oldest units built on it are now around 10 years old. The age printed in the serial number, the repair cost and the condition of the rest of the appliance decide it. Use the repair-or-replace guide.
Models built on the same platform
These models share this platform's service documentation, so fault codes and most diagnostic steps are the same.
Need your Whirlpool WFW5090JW repaired in the Las Vegas area?
We repair Whirlpool, Maytag, KitchenAid, JennAir, Amana and other Whirlpool-family appliances in Las Vegas, Henderson, Summerlin and Boulder City. A model number helps but is never required to book.