Model support
Whirlpool WTW5105HC Top-load washer
Troubleshooting, fault codes and repair information for the Whirlpool WTW5105HC, organized around the engineering platform this top-load washer is built on.
- Brand
- Whirlpool
- Model
- WTW5105HC
- Engineering revisions
- WTW5105HC, WTW5105HC0, WTW5105HC1, WTW5105HC2, WTW5105HC3, WTW5105HC4, WTW5105HC5, WTW5105HC6
- Appliance
- Top-load washer
- Platform
- Top-load washer platform, documentation from about 2019
- Models on this platform
- 6 across Whirlpool
- Documented fault codes
- 33 with explanations
- Service diagnostic mode
- Yes — a console-only test mode used by technicians to read stored codes and run component tests
- Service documentation
- Tech sheet, service manual (used by our technicians; not published)
Whirlpool WTW5105HC error codes
These are the fault codes documented for the platform this model belongs to. A code describes a condition the control detected; it does not by itself identify a failed part. Select a code for causes, safe checks and repair context.
| Code | Meaning | Areas involved |
|---|---|---|
| F0E2 | Too many suds | Water-level pressure sensor and hose, Main control board |
| F0E3 | Overload | Gearcase / transmission and basket drive, Drive motor, Main control board |
| F0E4 | Spin limited by water temperature | Water inlet valve, Temperature sensor (thermistor) |
| F0E5 | Off-balance load | Suspension rods, springs and dampers |
| F0E7 | Load detected during Clean Washer cycle | Gearcase / transmission and basket drive |
| F0E8 | Too much leftover water | Drain pump, Water-level pressure sensor and hose |
| F0E9 | Off-balance pause | Suspension rods, springs and dampers |
| F1E1 | Main control fault | Main control board |
| F1E2 | Motor drive voltage fault | Motor control / inverter board, Drive motor, Main control board |
| F2E1 | Stuck button | User interface / keypad board |
| F2E2 | Console disconnected | User interface / keypad board, Wiring harness and connectors, Main control board |
| F3E2 | Pressure system fault | Water-level pressure sensor and hose, Main control board |
| F3E3 | Inlet water temperature sensor fault | Temperature sensor (thermistor), Wiring harness and connectors |
| F3E5 | Bulk detergent system error | Detergent dispenser |
| F5E1 | Lid switch fault | Lid lock assembly, Main control board, Wiring harness and connectors |
| F5E3 | Lid will not unlock | Lid lock assembly, Main control board |
| F5E4 | Lid not opened between cycles | Lid lock assembly |
| F6E1 | Console and control not communicating | Wiring harness and connectors, Main control board, User interface / keypad board |
| F6E3 | Main control not receiving from motor control | Motor control / inverter board, Main control board, Wiring harness and connectors |
| F7E1 | Basket speed sensing fault | Drive motor, Shifter (shift actuator), Main control board |
| F7E2 | Motor drive failure | Motor control / inverter board, Drive motor, Main control board |
| F7E3 | Basket engaged during wash | Shifter (shift actuator), Agitator or wash plate, Wiring harness and connectors |
| F7E4 | Basket re-engagement failure | Shifter (shift actuator), Agitator or wash plate, Wiring harness and connectors |
| F7E6 | Motor circuit open | Drive motor, Wiring harness and connectors, Main control board |
| F7E7 | Motor unable to reach target speed | Drive motor, Gearcase / transmission and basket drive, Main control board |
| F7E8 | Motor drive overheating | Motor control / inverter board, Drive motor, Wiring harness and connectors |
| F7E9 | Locked rotor | Drive motor, Gearcase / transmission and basket drive, Main control board |
| F7EA | Motor phase lost | Drive motor, Wiring harness and connectors, Main control board |
| F8E1 | No fill or long fill | Water inlet valve, Water-level pressure sensor and hose, Main control board |
| F8E2 | Dispenser pump fault | Detergent dispenser, Wiring harness and connectors |
| F8E3 | Overflow | Water inlet valve, Water-level pressure sensor and hose, Main control board |
| F8E6 | Water hazard (water with lid open) | Water-level pressure sensor and hose, Water inlet valve, Lid lock assembly |
| F9E1 | Long drain | Drain pump, Water-level pressure sensor and hose, Main control board |
Common washer problems
- Not draining
Documented check order on this platform: Drain hose installation → Drain pump and pump inlet → Wiring and connectors → Main control board - Not spinning
Documented check order on this platform: Lid or door switch / lock → Wiring and connectors → Drive or pump motor → Main control board - Not filling
Documented check order on this platform: Drain hose installation → Inlet hose screens → Water inlet valve → Main control board - Not agitating
Documented check order on this platform: Lid or door switch / lock → Wiring and connectors → Drive or pump motor → Main control board - Leaking
Documented check order on this platform: Water inlet valve → Water-level pressure sensing → Main control board - Not starting
Documented check order on this platform: Power supply to the appliance → Lid or door switch / lock - Shaking or noisy
- Door or lid locked
- Stops mid-cycle
- Bad odor
Typical washer repair costs
| Repair | Typical range | Labor |
|---|---|---|
| Washer drain pump replacement | $180–$420 | Moderate |
| Washer water inlet valve replacement | $180–$360 | Light |
| Washer water-level pressure sensor repair | $180–$350 | Light |
| Top-load washer lid lock replacement | $180–$370 | Light |
| Washer drive motor replacement | $300–$720 | Heavy |
| Washer motor control board replacement | $280–$600 | Moderate |
| Top-load washer shifter replacement | $220–$460 | Moderate |
| Top-load washer gearcase / transmission replacement | $400–$880 | Major |
| Washer drive belt replacement | $180–$330 | Light |
| Washer suspension rods, springs or dampers replacement | $180–$440 | Moderate |
Typical total ranges for the Las Vegas area, parts and labor included. The final cost depends on diagnosis, the exact model, parts availability and whether other damage is found.
Repair or replace?
Washers typically last about 10–13 years. Service documentation for this platform dates from about 2019, so the oldest units built on it are now around 7 years old. The age printed in the serial number, the repair cost and the condition of the rest of the appliance decide it. Use the repair-or-replace guide.
Models built on the same platform
These models share this platform's service documentation, so fault codes and most diagnostic steps are the same.
Need your Whirlpool WTW5105HC repaired in the Las Vegas area?
We repair Whirlpool, Maytag, KitchenAid, JennAir, Amana and other Whirlpool-family appliances in Las Vegas, Henderson, Summerlin and Boulder City. A model number helps but is never required to book.