Whirlpool range F3E0: oven temperature sensor open or shorted
F3E0 means the control is getting an impossible reading from the main (or upper) oven temperature sensor, which points to an open or shorted sensor circuit.
What F3E0 means
- Brand
- Whirlpool
- Appliance
- Electric range, Gas range
- Code
- F3E0
- Documented meaning
- Oven temperature sensor open or shorted
- Applies to
- 557 Whirlpool models on 45 platforms
- Can you keep using it?
- With caution
What the range is detecting
The control reads the oven sensor's resistance to know cavity temperature. A reading that would mean extremely hot or below freezing, usually seconds after a cook or clean function starts, is treated as an open or shorted circuit and stops heating.
Causes listed for this condition
In the order the service documentation checks them. Documented causes come from the manufacturer's service documentation for these platforms; possible causes are based on how the system works; unconfirmed marks common assumptions that the documentation does not support.
- Documented A failed oven temperature sensor.
- Documented A loose, backed-out or damaged terminal or wire between the sensor and the control.
- Documented A control board fault in the sensor input, when the sensor and wiring test good.
Safe checks you can make
- Switch the oven off at the circuit breaker (or unplug it if the plug is easy to reach) for about one minute, restore power, and see whether the code comes back.
- Look inside the oven at the temperature sensor (a thin probe near the top rear corner); make sure it is not bent against the oven wall or loose. Do not remove it.
- Write down the full code exactly as shown (including any number after a dash) and when it appears; it speeds up diagnosis.
Further diagnosis requires opening the appliance. Beyond the owner checks, diagnosis involves removing panels, testing components and checking wiring. We describe what a technician investigates, not how to do it yourself.
What a technician checks
- Checks the sensor reading in service diagnostics at room temperature.
- Checks the sensor connector and harness for loose terminals or damage.
- Tests the sensor against specification before replacing it, then retests the control input.
Typical repairs and cost
Depending on what diagnosis finds, this code can lead to one of these repairs:
| Repair | Typical range | Labor |
|---|---|---|
| Oven temperature sensor replacement | $180–$320 | Light |
| Range control board replacement | $300–$720 | Moderate |
Typical total ranges for the Las Vegas area, parts and labor included. The final cost depends on diagnosis, the exact model, parts availability and whether other damage is found.
Can you keep using it?
Use with caution. The oven usually refuses to heat the affected cavity while this code is active. Do not keep restarting cook cycles; have the sensor circuit checked.
Whirlpool models documented with this code
- WEC310S0FB
- WEC310S0FS
- WEC310S0FW
- WEC310SAGB
- WEC310SAGS
- WEC310SAGW
- WEC530H0DB
- WEC530H0DS
- WEC530H0DW
- WEE510S0FB
- WEE510S0FS
- WEE510S0FV
- WEE510S0FW
- WEE510SAGB
- WEE510SAGS
- WEE510SAGW
And 541 more. Use the model lookup to check yours.
Related problems and codes
Other codes documented on the same Whirlpool platforms:
- F1E0
- F1E1
- F1E1-1
- F1E2
- F1E5
- F1E7
- F1E9
- F2E0
- F2E1
- F2E2
- F2E4
- F2E4-2
- F2E4-3
- F3E0-1
- F3E1
- F3E2
- F3E3
- F5E0
- F5E1
- F5E1-1
- F5E2
- F6E0
- F6E1
- F6E2
Repair or replace?
A fault code alone rarely justifies replacing a range. Most F3E0 repairs involve a single component once diagnosed. Replacement becomes worth considering when the unit is near the end of its typical 13–17-year life and the diagnosed repair is a major one. See the repair-or-replace guide.
Need F3E0 diagnosed in the Las Vegas area?
We repair Whirlpool, Maytag, KitchenAid, JennAir, Amana and other Whirlpool-family appliances in Las Vegas, Henderson, Summerlin and Boulder City. A model number helps but is never required to book.