Inglis washer F0E4 error code
F0E4 does not mean the same thing on every Inglis washer. Our data shows 2 documented meanings, depending on which engineering platform the model is built on. Look up your model number to see the one that applies.
| Meaning | Appliance | Inglis models |
|---|---|---|
| Rinse water too hot | Top-load washer | 11 |
| High water temperature | Front-load washer | 1 |
F0E4: Rinse water too hot
- Brand
- Inglis
- Appliance
- Top-load washer
- Code
- F0E4
- Documented meaning
- Rinse water too hot
- Applies to
- 11 Inglis models on 4 platforms
- Can you keep using it?
- With caution
F0E4 means the washer measured warm water during a rinse, when it expects cold, so hot water is reaching the tub when it should not.
What the washer is detecting
A temperature sensor in the water inlet reports the temperature of the incoming water. If the rinse water reads warmer than the limit the control allows, F0E4 is stored.
Causes listed for this condition
In the order the service documentation checks them. Documented causes come from the manufacturer's service documentation for these platforms; possible causes are based on how the system works; unconfirmed marks common assumptions that the documentation does not support.
- Documented Hot and cold fill hoses connected to the wrong faucets or to the wrong inlets on the washer.
- Documented An inlet temperature sensor (thermistor) that reads warmer than the real water temperature.
- Possible A hot side of the inlet valve that leaks or does not close fully.
Safe checks you can make
- Follow both fill hoses from the faucets to the back of the washer: the hose from the hot faucet should go to the inlet marked H (usually red), and the cold to C.
- Run a cold-water rinse and feel the incoming water. If it is warm with the hoses connected correctly, the problem is inside the washer.
Further diagnosis requires opening the appliance. Beyond the owner checks, diagnosis involves removing panels, testing components and checking wiring. We describe what a technician investigates, not how to do it yourself.
What a technician checks
- Checks the inlet temperature sensor reading against the actual water temperature.
- Checks that each side of the inlet valve opens and closes only when commanded.
Typical repairs and cost
Depending on what diagnosis finds, this code can lead to one of these repairs:
| Repair | Typical range | Labor |
|---|---|---|
| Washer water inlet valve replacement | $180–$360 | Light |
| Washer water temperature sensor replacement | $180–$310 | Light |
Typical total ranges for the Las Vegas area, parts and labor included. The final cost depends on diagnosis, the exact model, parts availability and whether other damage is found.
Can you keep using it?
Use with caution. The washer still works, but warm rinses can set wrinkles and shrink some fabrics. Correct reversed hoses before the next load.
Inglis models documented with this code
And 4 more. Use the model lookup to check yours.
F0E4: High water temperature
- Brand
- Inglis
- Appliance
- Front-load washer
- Code
- F0E4
- Documented meaning
- High water temperature
- Applies to
- 1 Inglis model on 1 platform
- Can you keep using it?
- With caution
F0E4 means the washer measured wash water hotter than the cycle allows.
What the washer is detecting
A temperature sensor in the tub reports the water temperature. When the reading is above the limit for the current step, the control flags F0E4. It can point at the water supply or at the sensing and heating parts.
Causes listed for this condition
In the order the service documentation checks them. Documented causes come from the manufacturer's service documentation for these platforms; possible causes are based on how the system works; unconfirmed marks common assumptions that the documentation does not support.
- Documented An inlet hose connected to the wrong faucet: hot and cold swapped, or, on models meant for a cold-water connection only, the hose attached to the hot faucet.
- Documented A wash heater that heats more than commanded.
- Documented A water temperature sensor reading higher than the real temperature.
Safe checks you can make
- Trace each inlet hose from the back of the washer to the faucet and make sure each is on the faucet the installation instructions call for (most connect hot to hot and cold to cold; cold-only models use just the cold faucet).
- Check your water heater setting; very hot household water can trip this code on some cycles.
Further diagnosis requires opening the appliance. Beyond the owner checks, diagnosis involves removing panels, testing components and checking wiring. We describe what a technician investigates, not how to do it yourself.
What a technician checks
- Checks the wash heater circuit for heating when it should be off.
- Compares the temperature sensor reading with the actual water temperature.
Typical repairs and cost
Depending on what diagnosis finds, this code can lead to one of these repairs:
| Repair | Typical range | Labor |
|---|---|---|
| Washer water temperature sensor replacement | $180–$310 | Light |
| Washer water inlet valve replacement | $180–$360 | Light |
| Washer main control board replacement | $300–$720 | Moderate |
Typical total ranges for the Las Vegas area, parts and labor included. The final cost depends on diagnosis, the exact model, parts availability and whether other damage is found.
Can you keep using it?
Use with caution. Fix the hose connections first. If the hoses are correct and the code returns, stop using heated cycles until the heater and sensor are checked.
Inglis models documented with this code
Related problems and codes
Other codes documented on the same Inglis platforms:
Repair or replace?
A fault code alone rarely justifies replacing a washer. Most F0E4 repairs involve a single component once diagnosed. Replacement becomes worth considering when the unit is near the end of its typical 10–13-year life and the diagnosed repair is a major one. See the repair-or-replace guide.
Need F0E4 diagnosed in the Las Vegas area?
We repair Whirlpool, Maytag, KitchenAid, JennAir, Amana and other Whirlpool-family appliances in Las Vegas, Henderson, Summerlin and Boulder City. A model number helps but is never required to book.