Inglis washer F1E2 error code
F1E2 does not mean the same thing on every Inglis washer. Our data shows 2 documented meanings, depending on which engineering platform the model is built on. Look up your model number to see the one that applies.
| Meaning | Appliance | Inglis models |
|---|---|---|
| Motor control fault | Top-load washer | 11 |
| Motor control fault | Front-load washer | 1 |
F1E2: Motor control fault
- Brand
- Inglis
- Appliance
- Top-load washer
- Code
- F1E2
- Documented meaning
- Motor control fault
- Applies to
- 11 Inglis models on 4 platforms
- Can you keep using it?
- No — stop and have it checked
F1E2 means the main control found a fault in its own motor-control section, the part of the board that drives the washer motor.
What the washer is detecting
On these models the electronics that run the motor are part of the main control. When that section reports an internal fault, F1E2 is stored and the motor is stopped.
Causes listed for this condition
In the order the service documentation checks them. Documented causes come from the manufacturer's service documentation for these platforms; possible causes are based on how the system works; unconfirmed marks common assumptions that the documentation does not support.
- Documented A fault in the motor-control circuitry of the main control.
- Documented A motor or motor wiring problem that the motor test is used to rule out.
Safe checks you can make
- Unplug the washer for one minute, plug it back in and start a new cycle. If the code comes straight back, the condition is persistent and needs diagnosis.
This stage requires professional testing. Full diagnosis involves hazards such as live line voltage, gas, a sealed refrigerant system or microwave high voltage. Do not attempt it yourself.
What a technician checks
- Runs the drive-motor test from service diagnostics.
- Checks the motor and its harness before replacing the control.
Typical repairs and cost
Depending on what diagnosis finds, this code can lead to one of these repairs:
| Repair | Typical range | Labor |
|---|---|---|
| Washer main control board replacement | $300–$720 | Moderate |
| Washer drive motor replacement | $300–$720 | Heavy |
Typical total ranges for the Las Vegas area, parts and labor included. The final cost depends on diagnosis, the exact model, parts availability and whether other damage is found.
Can you keep using it?
Stop using it until it is checked. Stop using the washer if the code returns after a power reset. Motor drive electronics can hold stored energy, so this requires professional testing.
Inglis models documented with this code
And 4 more. Use the model lookup to check yours.
F1E2: Motor control fault
- Brand
- Inglis
- Appliance
- Front-load washer
- Code
- F1E2
- Documented meaning
- Motor control fault
- Applies to
- 1 Inglis model on 1 platform
- Can you keep using it?
- With caution
F1E2 means the part of the electronics that drives the motor reported a fault, such as supply power out of range, excess current or an internal malfunction.
What the washer is detecting
The motor control circuit (a separate board on older models, a section of the main control on newer ones) watches its own supply and current. Repeated under-supply, over-supply or over-current events, or an internal failure, set F1E2.
Causes listed for this condition
In the order the service documentation checks them. Documented causes come from the manufacturer's service documentation for these platforms; possible causes are based on how the system works; unconfirmed marks common assumptions that the documentation does not support.
- Documented Household supply problems: a weak or interrupted circuit, a loose neutral connection, or a power disturbance during spin.
- Documented An internal fault in the motor control circuit.
- Documented A wiring problem between the control and the motor.
- Possible A motor fault that draws excess current.
Safe checks you can make
- Unplug the washer (or switch off its breaker) for one minute, then restore power and start a new cycle to see whether the code comes back. A code that returns right away points to a fault that needs diagnosis.
- Make sure the washer is plugged directly into a properly grounded wall outlet, without an extension cord or adapter.
- On some older models the door stays locked for a few minutes after this code appears during a high-speed spin; wait before trying to open it.
This stage requires professional testing. Full diagnosis involves hazards such as live line voltage, gas, a sealed refrigerant system or microwave high voltage. Do not attempt it yourself.
What a technician checks
- Checks the household circuit and the supply reaching the washer.
- Runs the motor circuit test and inspects the motor wiring.
- Decides between the motor control circuit and the motor itself. Supply checks require professional testing because line voltage is present.
Typical repairs and cost
Depending on what diagnosis finds, this code can lead to one of these repairs:
| Repair | Typical range | Labor |
|---|---|---|
| Washer motor control board replacement | $280–$600 | Moderate |
| Washer main control board replacement | $300–$720 | Moderate |
| Washer drive motor replacement | $300–$720 | Heavy |
Typical total ranges for the Las Vegas area, parts and labor included. The final cost depends on diagnosis, the exact model, parts availability and whether other damage is found.
Can you keep using it?
Use with caution. If the code keeps returning, stop using the washer. Repeated motor-control faults can leave water in the tub and the door locked.
Inglis models documented with this code
Related problems and codes
Other codes documented on the same Inglis platforms:
Repair or replace?
A fault code alone rarely justifies replacing a washer. Most F1E2 repairs involve a single component once diagnosed. Replacement becomes worth considering when the unit is near the end of its typical 10–13-year life and the diagnosed repair is a major one. See the repair-or-replace guide.
Need F1E2 diagnosed in the Las Vegas area?
We repair Whirlpool, Maytag, KitchenAid, JennAir, Amana and other Whirlpool-family appliances in Las Vegas, Henderson, Summerlin and Boulder City. A model number helps but is never required to book.