KitchenAid range F3E1 error code
F3E1 does not mean the same thing on every KitchenAid range. Our data shows 2 documented meanings, depending on which engineering platform the model is built on. Look up your model number to see the one that applies.
| Meaning | Appliance | KitchenAid models |
|---|---|---|
| Second oven sensor open or shorted | Ranges | 51 |
| Oven sensor shorted | Ranges | 38 |
F3E1: Second oven sensor open or shorted
- Brand
- KitchenAid
- Appliance
- Dual-fuel range, Gas range
- Code
- F3E1
- Documented meaning
- Second oven sensor open or shorted
- Applies to
- 51 KitchenAid models on 7 platforms
- Can you keep using it?
- With caution
F3E1 means the control is getting an impossible reading from the temperature sensor of the second oven cavity: the lower oven of a double wall oven or the left oven of a double-oven range.
What the range is detecting
Each cavity has its own temperature sensor. When the second cavity's sensor reads as extremely hot or below freezing, the control treats the circuit as open or shorted and stops heating that cavity.
Causes listed for this condition
In the order the service documentation checks them. Documented causes come from the manufacturer's service documentation for these platforms; possible causes are based on how the system works; unconfirmed marks common assumptions that the documentation does not support.
- Documented A failed temperature sensor in the second oven.
- Documented A loose or damaged connection between that sensor and the control.
- Documented A control board fault in that sensor input.
Safe checks you can make
- Switch the oven off at the circuit breaker (or unplug it if the plug is easy to reach) for about one minute, restore power, and see whether the code comes back.
- Look inside the oven at the temperature sensor (a thin probe near the top rear corner); make sure it is not bent against the oven wall or loose. Do not remove it.
- Write down the full code exactly as shown (including any number after a dash) and when it appears; it speeds up diagnosis.
Further diagnosis requires opening the appliance. Beyond the owner checks, diagnosis involves removing panels, testing components and checking wiring. We describe what a technician investigates, not how to do it yourself.
What a technician checks
- Checks the sensor reading in service diagnostics at room temperature.
- Checks the sensor connector and harness for loose terminals or damage.
- Tests the sensor against specification before replacing it, then retests the control input.
Typical repairs and cost
Depending on what diagnosis finds, this code can lead to one of these repairs:
| Repair | Typical range | Labor |
|---|---|---|
| Oven temperature sensor replacement | $180–$320 | Light |
| Range control board replacement | $300–$720 | Moderate |
Typical total ranges for the Las Vegas area, parts and labor included. The final cost depends on diagnosis, the exact model, parts availability and whether other damage is found.
Can you keep using it?
Use with caution. The oven usually refuses to heat the affected cavity while this code is active. Do not keep restarting cook cycles; have the sensor circuit checked.
KitchenAid models documented with this code
- KFDC500HSS
- KFDC500JSS
- KFDC506HSS
- KFDC506JSS
- KFDC558HSS
- KFDC558JSS
- KFDD948SAG
- KFDD948SBE
- KFDD948SDC
- KFDD948SJP
- KFDD948SPL
- KFDD948SSC
- KFDD948SSS
- KFDD948SWF
- KFGD500EBL
- KFGD500ESS010
And 35 more. Use the model lookup to check yours.
F3E1: Oven sensor shorted
- Brand
- KitchenAid
- Appliance
- Dual-fuel range, Electric range, Gas range
- Code
- F3E1
- Documented meaning
- Oven sensor shorted
- Applies to
- 38 KitchenAid models on 6 platforms
- Can you keep using it?
- With caution
F3E1 means the range control is reading its oven temperature sensor as shorted, an impossible value that stops the oven from heating.
What the range is detecting
On these single-oven range controls F3E0 covers an open sensor and F3E1 a shorted one. Both are checked the same way: sensor, wiring, then the control input.
Causes listed for this condition
In the order the service documentation checks them. Documented causes come from the manufacturer's service documentation for these platforms; possible causes are based on how the system works; unconfirmed marks common assumptions that the documentation does not support.
- Documented A shorted oven temperature sensor.
- Documented A pinched or damaged wire, or a sensor body shorted to the oven cavity.
- Possible A control board fault in the sensor input.
Safe checks you can make
- Switch the oven off at the circuit breaker (or unplug it if the plug is easy to reach) for about one minute, restore power, and see whether the code comes back.
- Look inside the oven at the temperature sensor (a thin probe near the top rear corner); make sure it is not bent against the oven wall or loose. Do not remove it.
- Write down the full code exactly as shown (including any number after a dash) and when it appears; it speeds up diagnosis.
Further diagnosis requires opening the appliance. Beyond the owner checks, diagnosis involves removing panels, testing components and checking wiring. We describe what a technician investigates, not how to do it yourself.
What a technician checks
- Checks the sensor reading in service diagnostics at room temperature.
- Checks the sensor connector and harness for loose terminals or damage.
- Tests the sensor against specification before replacing it, then retests the control input.
Typical repairs and cost
Depending on what diagnosis finds, this code can lead to one of these repairs:
| Repair | Typical range | Labor |
|---|---|---|
| Oven temperature sensor replacement | $180–$320 | Light |
| Range control board replacement | $300–$720 | Moderate |
Typical total ranges for the Las Vegas area, parts and labor included. The final cost depends on diagnosis, the exact model, parts availability and whether other damage is found.
Can you keep using it?
Use with caution. The oven usually refuses to heat the affected cavity while this code is active. Do not keep restarting cook cycles; have the sensor circuit checked.
KitchenAid models documented with this code
- KFEG500EBL
- KFEG500EBS
- KFEG500ESS
- KFEG500EWH
- KFGG500EBL
- KSDB900EBS
- KSEB900EBL
- KSEB900EBS
- KSEB900ESS
- KSEB900EWH
- KSEG700EBL
- KSEG700EBS
- KSEG700ESS
- KSEG700EWH
- KSEG950ESS
- KSGB900EBL
And 22 more. Use the model lookup to check yours.
Related problems and codes
Other codes documented on the same KitchenAid platforms:
Repair or replace?
A fault code alone rarely justifies replacing a range. Most F3E1 repairs involve a single component once diagnosed. Replacement becomes worth considering when the unit is near the end of its typical 13–17-year life and the diagnosed repair is a major one. See the repair-or-replace guide.
Need F3E1 diagnosed in the Las Vegas area?
We repair Whirlpool, Maytag, KitchenAid, JennAir, Amana and other Whirlpool-family appliances in Las Vegas, Henderson, Summerlin and Boulder City. A model number helps but is never required to book.