Maytag range F3E2 error code
F3E2 does not mean the same thing on every Maytag range. Our data shows 2 documented meanings, depending on which engineering platform the model is built on. Look up your model number to see the one that applies.
| Meaning | Appliance | Maytag models |
|---|---|---|
| Bake/broil over temperature | Ranges | 89 |
| Warming drawer sensor open or shorted | Ranges | 31 |
F3E2: Bake/broil over temperature
- Brand
- Maytag
- Appliance
- Electric range, Gas range
- Code
- F3E2
- Documented meaning
- Bake/broil over temperature
- Applies to
- 89 Maytag models on 12 platforms
- Can you keep using it?
- No — stop and have it checked
F3E2 means the range control detected an oven temperature above its safe limit during baking or broiling.
What the range is detecting
These range controls check the oven sensor reading against a ceiling for normal cooking. A reading above it during bake or broil sets F3E2; the documented checks start with the sensor and its wiring.
Causes listed for this condition
In the order the service documentation checks them. Documented causes come from the manufacturer's service documentation for these platforms; possible causes are based on how the system works; unconfirmed marks common assumptions that the documentation does not support.
- Documented An oven temperature sensor or sensor wiring giving a falsely high reading.
- Possible A heating circuit that stays on when the control should have switched it off.
Safe checks you can make
- If you smell gas at any point, do not touch switches or controls; leave the home and call your gas utility or 911 from outside.
- Let the oven cool down completely before trying another cycle.
- Switch the oven off at the circuit breaker (or unplug it if the plug is easy to reach) for about one minute, restore power, and see whether the code comes back.
This stage requires professional testing. Full diagnosis involves hazards such as live line voltage, gas, a sealed refrigerant system or microwave high voltage. Do not attempt it yourself.
What a technician checks
- Compares the actual cavity temperature with the control's reading to separate a false reading from real overheating.
- Checks the oven sensor and its wiring.
- This requires professional testing: finding a heating circuit that stays powered means working on live line-voltage circuits.
Typical repairs and cost
Depending on what diagnosis finds, this code can lead to one of these repairs:
| Repair | Typical range | Labor |
|---|---|---|
| Oven temperature sensor replacement | $180–$320 | Light |
| Range control board replacement | $300–$720 | Moderate |
Typical total ranges for the Las Vegas area, parts and labor included. The final cost depends on diagnosis, the exact model, parts availability and whether other damage is found.
Can you keep using it?
Stop using it until it is checked. Turn the oven off and do not use it until it is checked. If it keeps heating with no cook function selected, switch the circuit breaker off. On a gas range, if you smell gas, leave the home and call the gas utility.
Maytag models documented with this code
- MER4600LS
- MER6600FB
- MER6600FS
- MER6600FW
- MER6600FZ
- MER7685BB
- MER7685BS
- MER7685BW
- MER7700LZ
- MER8600DE
- MER8600DH
- MER8600DS
- MER8650DE
- MER8650DH
- MER8650DS
- MER8650ES
And 73 more. Use the model lookup to check yours.
F3E2: Warming drawer sensor open or shorted
- Brand
- Maytag
- Appliance
- Electric range, Gas range
- Code
- F3E2
- Documented meaning
- Warming drawer sensor open or shorted
- Applies to
- 31 Maytag models on 3 platforms
- Can you keep using it?
- With caution
F3E2 means the control is getting an impossible reading from the warming drawer's temperature sensor, which points to an open or shorted circuit.
What the range is detecting
Models with an electronic warming drawer read its temperature with a separate sensor. A reading that would mean extremely hot or below freezing stops the drawer and sets F3E2.
Causes listed for this condition
In the order the service documentation checks them. Documented causes come from the manufacturer's service documentation for these platforms; possible causes are based on how the system works; unconfirmed marks common assumptions that the documentation does not support.
- Documented A failed warming drawer temperature sensor.
- Documented A loose or damaged connection in the drawer sensor wiring.
- Possible A control input fault.
Safe checks you can make
- Switch the oven off at the circuit breaker (or unplug it if the plug is easy to reach) for about one minute, restore power, and see whether the code comes back.
- Write down the full code exactly as shown (including any number after a dash) and when it appears; it speeds up diagnosis.
Further diagnosis requires opening the appliance. Beyond the owner checks, diagnosis involves removing panels, testing components and checking wiring. We describe what a technician investigates, not how to do it yourself.
What a technician checks
- Checks the sensor reading in service diagnostics at room temperature.
- Checks the sensor connector and harness for loose terminals or damage.
- Tests the sensor against specification before replacing it, then retests the control input.
Typical repairs and cost
Depending on what diagnosis finds, this code can lead to one of these repairs:
| Repair | Typical range | Labor |
|---|---|---|
| Oven temperature sensor replacement | $180–$320 | Light |
| Range control board replacement | $300–$720 | Moderate |
Typical total ranges for the Las Vegas area, parts and labor included. The final cost depends on diagnosis, the exact model, parts availability and whether other damage is found.
Can you keep using it?
Use with caution. The oven itself may still work, but the warming drawer will not heat correctly until the sensor circuit is repaired. Do not keep restarting the drawer.
Maytag models documented with this code
- MER8800DE
- MER8800DH
- MER8800DS
- MER8800FB
- MER8800FW
- MER8800HK
- MGR8800DE
- MGR8800DH
- MGR8800DS
- MGR8800FB
- MGR8800FE
- MGR8800FH
- MGR8800FW
- MGR8800HK
- MGR8850DS
- MGS8880DE
And 15 more. Use the model lookup to check yours.
Related problems and codes
Other codes documented on the same Maytag platforms:
Repair or replace?
A fault code alone rarely justifies replacing a range. Most F3E2 repairs involve a single component once diagnosed. Replacement becomes worth considering when the unit is near the end of its typical 13–17-year life and the diagnosed repair is a major one. See the repair-or-replace guide.
Need F3E2 diagnosed in the Las Vegas area?
We repair Whirlpool, Maytag, KitchenAid, JennAir, Amana and other Whirlpool-family appliances in Las Vegas, Henderson, Summerlin and Boulder City. A model number helps but is never required to book.