Maytag MTW5600RU Top-load washer
Troubleshooting, fault codes and repair information for the Maytag MTW5600RU, organized around the engineering platform this top-load washer is built on.
- Brand
- Maytag
- Model
- MTW5600RU
- Engineering revisions
- MTW5600RU0, MTW5600RU1
- Appliance
- Top-load washer
- Platform
- Top-load washer platform, documentation from about 2021
- Models on this platform
- 11 across Maytag
- Documented fault codes
- 24 with explanations
- Service diagnostic mode
- Yes — a console-only test mode used by technicians to read stored codes and run component tests
- Service documentation
- Tech sheet, service manual (used by our technicians; not published)
Maytag MTW5600RU error codes
These are the fault codes documented for the platform this model belongs to. A code describes a condition the control detected; it does not by itself identify a failed part. Select a code for causes, safe checks and repair context.
| Code | Meaning | Areas involved |
|---|---|---|
| F0E2 | Too many suds | Water-level pressure sensor and hose, Main control board |
| F0E3 | Overload | Gearcase / transmission and basket drive, Drive motor, Main control board |
| F0E4 | Spin limited by water temperature | Water inlet valve, Temperature sensor (thermistor) |
| F0E5 | Off-balance load | Suspension rods, springs and dampers |
| F0E7 | Load detected during Clean Washer cycle | Gearcase / transmission and basket drive |
| F0E8 | Too much leftover water | Drain pump, Water-level pressure sensor and hose |
| F0E9 | Off-balance pause | Suspension rods, springs and dampers |
| F1E1 | Main control fault | Main control board |
| F2E1 | Stuck button | User interface / keypad board |
| F2E2 | Console disconnected | User interface / keypad board, Wiring harness and connectors, Main control board |
| F3E2 | Pressure system fault | Water-level pressure sensor and hose, Main control board |
| F5E1 | Lid switch fault | Lid lock assembly, Main control board, Wiring harness and connectors |
| F5E3 | Lid will not unlock | Lid lock assembly, Main control board |
| F5E4 | Lid not opened between cycles | Lid lock assembly |
| F6E1 | Console and control not communicating | Wiring harness and connectors, Main control board, User interface / keypad board |
| F7E1 | Basket speed sensing fault | Drive motor, Shifter (shift actuator), Main control board |
| F7E3 | Basket engaged during wash | Shifter (shift actuator), Agitator or wash plate, Wiring harness and connectors |
| F7E4 | Basket re-engagement failure | Shifter (shift actuator), Agitator or wash plate, Wiring harness and connectors |
| F7E6 | Motor circuit open | Drive motor, Wiring harness and connectors, Main control board |
| F7E7 | Motor unable to reach target speed | Drive motor, Gearcase / transmission and basket drive, Main control board |
| F8E1 | No fill or long fill | Water inlet valve, Water-level pressure sensor and hose, Main control board |
| F8E3 | Overflow | Water inlet valve, Water-level pressure sensor and hose, Main control board |
| F8E6 | Water hazard (water with lid open) | Water-level pressure sensor and hose, Water inlet valve, Lid lock assembly |
| F9E1 | Long drain | Drain pump, Water-level pressure sensor and hose, Main control board |
Common washer problems
- Not draining
Documented check order on this platform: Drain hose installation → Drain pump and pump inlet → Wiring and connectors → Main control board - Not spinning
Documented check order on this platform: Lid or door switch / lock → Wiring and connectors → Shifter → Drive or pump motor → Main control board - Not filling
Documented check order on this platform: Inlet hose screens → Drain hose installation → Water inlet valve → Main control board - Not agitating
Documented check order on this platform: Lid or door switch / lock → Wiring and connectors → Shifter → Drive or pump motor → Main control board - Leaking
Documented check order on this platform: Water-level pressure sensing → Water inlet valve → Main control board - Not starting
Documented check order on this platform: Power supply to the appliance → Wiring and connectors → User interface / keypad → Main control board → Lid or door switch / lock - Shaking or noisy
- Door or lid locked
- Stops mid-cycle
- Bad odor
Typical washer repair costs
| Repair | Typical range | Labor |
|---|---|---|
| Washer drain pump replacement | $180–$420 | Moderate |
| Washer water inlet valve replacement | $180–$360 | Light |
| Washer water-level pressure sensor repair | $180–$350 | Light |
| Top-load washer lid lock replacement | $180–$370 | Light |
| Washer drive motor replacement | $300–$720 | Heavy |
| Washer motor control board replacement | $280–$600 | Moderate |
| Top-load washer shifter replacement | $220–$460 | Moderate |
| Top-load washer gearcase / transmission replacement | $400–$880 | Major |
| Washer drive belt replacement | $180–$330 | Light |
| Washer suspension rods, springs or dampers replacement | $180–$440 | Moderate |
Typical total ranges for the Las Vegas area, parts and labor included. The final cost depends on diagnosis, the exact model, parts availability and whether other damage is found.
Repair or replace?
Washers typically last about 10–13 years. Service documentation for this platform dates from about 2021, so the oldest units built on it are now around 5 years old. The age printed in the serial number, the repair cost and the condition of the rest of the appliance decide it. Use the repair-or-replace guide.
Models built on the same platform
These models share this platform's service documentation, so fault codes and most diagnostic steps are the same.
- Maytag MTW5205TW
- Maytag MTW5600RW
- Maytag MTW5605RU
- Maytag MTW5605RW
- Maytag MVW4505MW
- Maytag MVW5035MW
- Maytag MVW5430MW
- Maytag MVW5430PBK
- Maytag MVW5435PBK
- Maytag MVW5435PW
Need your Maytag MTW5600RU repaired in the Las Vegas area?
We repair Whirlpool, Maytag, KitchenAid, JennAir, Amana and other Whirlpool-family appliances in Las Vegas, Henderson, Summerlin and Boulder City. A model number helps but is never required to book.