Maytag washer F8E1 error code
F8E1 does not mean the same thing on every Maytag washer. Our data shows 2 documented meanings, depending on which engineering platform the model is built on. Look up your model number to see the one that applies.
| Meaning | Appliance | Maytag models |
|---|---|---|
| No fill or long fill | Top-load washer | 87 |
| Long fill / no fill | Front-load washer | 47 |
F8E1: No fill or long fill
- Brand
- Maytag
- Appliance
- Top-load washer
- Code
- F8E1
- Documented meaning
- No fill or long fill
- Applies to
- 87 Maytag models on 18 platforms
- Can you keep using it?
- With caution
F8E1 means the washer was filling but the control did not see the water level rise within the time it allows.
What the washer is detecting
The control opens the inlet valve and watches the level reading. If the level does not change for too long, or water is present but the reading does not move, F8E1 is stored.
Causes listed for this condition
In the order the service documentation checks them. Documented causes come from the manufacturer's service documentation for these platforms; possible causes are based on how the system works; unconfirmed marks common assumptions that the documentation does not support.
- Documented Water supply not connected or faucets turned off, or supply hoses kinked.
- Documented Clogged inlet screens or low household water pressure.
- Documented A drain hose that siphons water out as fast as it comes in, often because it is pushed too far into or sealed into the standpipe.
- Documented A pinched, plugged or leaking pressure hose, so the control does not see the level change.
- Documented An inlet valve that does not open, checked with the valve test.
Safe checks you can make
- Make sure both water faucets behind the washer are fully open and the fill hoses are not kinked behind the cabinet.
- Turn off the faucets, remove the fill hoses at the washer and check the small screens inside the inlet ports for grit; rinse them if needed.
- Check that the drain hose hangs loosely in the standpipe or laundry tub with an air gap around it, is not taped or sealed in, and is not pushed deep into the pipe; a sealed or deep hose can siphon water out while the washer fills.
- Check another faucet in the house for normal pressure.
Further diagnosis requires opening the appliance. Beyond the owner checks, diagnosis involves removing panels, testing components and checking wiring. We describe what a technician investigates, not how to do it yourself.
What a technician checks
- Runs the inlet valve test.
- Checks the pressure hose and the level reading during fill.
Typical repairs and cost
Depending on what diagnosis finds, this code can lead to one of these repairs:
| Repair | Typical range | Labor |
|---|---|---|
| Washer water inlet valve replacement | $180–$360 | Light |
| Washer water-level pressure sensor repair | $180–$350 | Light |
| Washer main control board replacement | $300–$720 | Moderate |
Typical total ranges for the Las Vegas area, parts and labor included. The final cost depends on diagnosis, the exact model, parts availability and whether other damage is found.
Can you keep using it?
Use with caution. Fix the supply or drain-hose issue first. If the washer still does not fill, stop and have the valve and level sensing checked; a siphoning drain hose wastes water and can leave loads unrinsed.
Maytag models documented with this code
- MTW4200SW
- MTW4205SW
- MTW5205TW
- MTW5600RU
- MTW5600RW
- MTW5605RU
- MTW5605RW
- MTW6200RF
- MTW6200RR
- MTW6200RW
- MTW6205RF
- MTW6205RR
- MTW6205RW
- MTW7200RF
- MTW7200RR
- MTW7200RW
And 71 more. Use the model lookup to check yours.
F8E1: Long fill / no fill
- Brand
- Maytag
- Appliance
- Front-load washer
- Code
- F8E1
- Documented meaning
- Long fill / no fill
- Applies to
- 47 Maytag models on 6 platforms
- Can you keep using it?
- With caution
F8E1 means the washer has been filling longer than it allows without seeing the water level rise enough.
What the washer is detecting
While filling, the control watches the water level. When the level does not change for too long, or water is present but the level reading does not change, it stops with F8E1. Some displays show Lo FL.
Causes listed for this condition
In the order the service documentation checks them. Documented causes come from the manufacturer's service documentation for these platforms; possible causes are based on how the system works; unconfirmed marks common assumptions that the documentation does not support.
- Documented Water supply off, or a kinked inlet hose.
- Documented Low water pressure or plugged screens in the inlet hoses.
- Documented A drain hose pushed too far into the standpipe or sealed in, which siphons water out as it fills.
- Documented A pinched, plugged or leaking pressure hose, so the control cannot see the level change.
- Documented An inlet valve that does not open.
Safe checks you can make
- Make sure both faucets are fully open and the inlet hoses are not kinked behind the washer.
- Turn off the faucets, disconnect the hoses at the washer and clean any debris from the small screens at the hose ends, then reconnect and check for leaks.
- Check the drain hose: it should hang loosely in the standpipe, only a few inches in, with an air gap around it, not taped or sealed.
- If other faucets in the house have low pressure, the cause may be the household supply.
Further diagnosis requires opening the appliance. Beyond the owner checks, diagnosis involves removing panels, testing components and checking wiring. We describe what a technician investigates, not how to do it yourself.
What a technician checks
- Runs the water inlet valve test.
- Checks the pressure hose and the level sensor reading during fill.
Typical repairs and cost
Depending on what diagnosis finds, this code can lead to one of these repairs:
| Repair | Typical range | Labor |
|---|---|---|
| Washer water inlet valve replacement | $180–$360 | Light |
| Washer water-level pressure sensor repair | $180–$350 | Light |
| Washer main control board replacement | $300–$720 | Moderate |
Typical total ranges for the Las Vegas area, parts and labor included. The final cost depends on diagnosis, the exact model, parts availability and whether other damage is found.
Can you keep using it?
Use with caution. Fix the supply and hose checks first. If the code returns, stop running cycles until the valve and level sensing are checked.
Maytag models documented with this code
- MFW7020RF
- MFW7020RU
- MFW7020RW
- MHW3100DW
- MHW3500BW
- MHW3500FW
- MHW3505FW
- MHW4100DW
- MHW4300DC
- MHW4300DW
- MHW5100DC
- MHW5100DW
- MHW5400DC
- MHW5400DW
- MHW5500FC
- MHW5500FW
And 31 more. Use the model lookup to check yours.
Related problems and codes
Other codes documented on the same Maytag platforms:
Repair or replace?
A fault code alone rarely justifies replacing a washer. Most F8E1 repairs involve a single component once diagnosed. Replacement becomes worth considering when the unit is near the end of its typical 10–13-year life and the diagnosed repair is a major one. See the repair-or-replace guide.
Need F8E1 diagnosed in the Las Vegas area?
We repair Whirlpool, Maytag, KitchenAid, JennAir, Amana and other Whirlpool-family appliances in Las Vegas, Henderson, Summerlin and Boulder City. A model number helps but is never required to book.