Maytag MVWC400XW Top-load washer
Troubleshooting, fault codes and repair information for the Maytag MVWC400XW, organized around the engineering platform this top-load washer is built on.
- Brand
- Maytag
- Model
- MVWC400XW
- Engineering revisions
- MVWC400XW, MVWC400XW0, MVWC400XW1, MVWC400XW2, MVWC400XW3, MVWC400XW4
- Appliance
- Top-load washer
- Platform
- Top-load washer platform, documentation from about 2011
- Models on this platform
- 30 across Admiral, Amana, Crosley, Inglis, Maytag, Roper, Whirlpool
- Documented fault codes
- 21 with explanations
- Service diagnostic mode
- Yes — a console-only test mode used by technicians to read stored codes and run component tests
- Service documentation
- Tech sheet, service manual (used by our technicians; not published)
Revision matters. Different engineering revisions of this model are documented on more than one platform. Confirm the full model number, including the last digit, on the model tag.
Maytag MVWC400XW error codes
These are the fault codes documented for the platform this model belongs to. A code describes a condition the control detected; it does not by itself identify a failed part. Select a code for causes, safe checks and repair context.
| Code | Meaning | Areas involved |
|---|---|---|
| F0E2 | Too many suds | Water-level pressure sensor and hose, Main control board |
| F0E4 | Rinse water too hot | Water inlet valve, Temperature sensor (thermistor) |
| F0E5 | Off-balance load | Suspension rods, springs and dampers |
| F1E1 | Main control fault | Main control board |
| F1E2 | Motor control fault | Main control board, Drive motor, Wiring harness and connectors |
| F2E1 | Stuck button | User interface / keypad board |
| F2E3 | Control and console mismatch | Main control board, User interface / keypad board |
| F3E1 | Pressure system fault | Water-level pressure sensor and hose, Main control board, Wiring harness and connectors |
| F3E2 | Inlet water temperature sensor fault | Temperature sensor (thermistor), Wiring harness and connectors, Main control board |
| F5E1 | Lid switch fault | Lid lock assembly, Main control board, Wiring harness and connectors |
| F5E2 | Lid will not lock | Lid lock assembly, Main control board |
| F5E3 | Lid will not unlock | Lid lock assembly, Main control board |
| F5E4 | Lid not opened between cycles | Lid lock assembly |
| F7E1 | Basket speed sensing fault | Drive motor, Shifter (shift actuator), Main control board |
| F7E5 | Shifter fault | Shifter (shift actuator), Wiring harness and connectors, Main control board |
| F7E6 | Motor circuit open | Drive motor, Wiring harness and connectors, Main control board |
| F7E7 | Motor unable to reach target speed | Drive motor, Gearcase / transmission and basket drive, Main control board |
| F8E1 | No fill or long fill | Water inlet valve, Water-level pressure sensor and hose, Main control board |
| F8E3 | Overflow | Water inlet valve, Water-level pressure sensor and hose, Main control board |
| F8E5 | Hot and cold reversed | Water inlet valve, Temperature sensor (thermistor) |
| F9E1 | Long drain | Drain pump, Water-level pressure sensor and hose, Main control board |
Common washer problems
- Not draining
Documented check order on this platform: Drain hose installation → Drain pump and pump inlet → Wiring and connectors → Main control board - Not spinning
Documented check order on this platform: Lid or door switch / lock → Drive belt → Wiring and connectors → Shifter → Drive or pump motor - Not filling
Documented check order on this platform: Inlet hose screens → Drain hose installation → Water inlet valve → Main control board - Not agitating
Documented check order on this platform: Lid or door switch / lock → Drive belt → Wiring and connectors → Shifter → Drive or pump motor - Leaking
Documented check order on this platform: Water-level pressure sensing → Water inlet valve → Main control board - Not starting
Documented check order on this platform: Power supply to the appliance → Wiring and connectors → User interface / keypad → Main control board → Lid or door switch / lock - Shaking or noisy
- Door or lid locked
- Stops mid-cycle
- Bad odor
Typical washer repair costs
| Repair | Typical range | Labor |
|---|---|---|
| Washer drain pump replacement | $180–$420 | Moderate |
| Washer water inlet valve replacement | $180–$360 | Light |
| Washer water-level pressure sensor repair | $180–$350 | Light |
| Top-load washer lid lock replacement | $180–$370 | Light |
| Washer drive motor replacement | $300–$720 | Heavy |
| Washer motor control board replacement | $280–$600 | Moderate |
| Top-load washer shifter replacement | $220–$460 | Moderate |
| Top-load washer gearcase / transmission replacement | $400–$880 | Major |
| Washer drive belt replacement | $180–$330 | Light |
| Washer suspension rods, springs or dampers replacement | $180–$440 | Moderate |
Typical total ranges for the Las Vegas area, parts and labor included. The final cost depends on diagnosis, the exact model, parts availability and whether other damage is found.
Repair or replace?
Washers typically last about 10–13 years. Service documentation for this platform dates from about 2011, so the oldest units built on it are now around 15 years old. The age printed in the serial number, the repair cost and the condition of the rest of the appliance decide it. Use the repair-or-replace guide.
Models built on the same platform
These models share this platform's service documentation, so fault codes and most diagnostic steps are the same.
- Whirlpool WTW4700YQ
- Whirlpool WTW4750YQ
- Whirlpool WTW4800XQ
- Whirlpool WTW4820XQ
- Whirlpool WTW4850XQ
- Whirlpool WTW4880AW
- Whirlpool WTW4900XQ
- Whirlpool WTW4900XW
- Whirlpool WTW4910XQ
- Whirlpool WTW4930XW
- Whirlpool WTW4950XW
- Admiral ATW4675YQ
- Crosley CAW12444XW
- Crosley CAW9244XQ
- Crosley CAW9444XQ
- Inglis ITW4600YQ
- Inglis ITW4700YQ
- Maytag MVWC100YQ
- Maytag MVWC200XW
- Maytag MVWC300XW
- Maytag MVWC350AW
- Maytag MVWC400BW
- Maytag MVWC450XW
- Amana NTW4501XQ
- Amana NTW4600YQ
- Amana NTW4601XQ
- Amana NTW4700YQ
- Amana NTW4750YQ
- Roper RTW4640YQ
Need your Maytag MVWC400XW repaired in the Las Vegas area?
We repair Whirlpool, Maytag, KitchenAid, JennAir, Amana and other Whirlpool-family appliances in Las Vegas, Henderson, Summerlin and Boulder City. A model number helps but is never required to book.