Model support
Maytag MVWB855DC Top-load washer
Troubleshooting, fault codes and repair information for the Maytag MVWB855DC, organized around the engineering platform this top-load washer is built on.
- Brand
- Maytag
- Model
- MVWB855DC
- Engineering revisions
- MVWB855DC, MVWB855DC0, MVWB855DC1, MVWB855DC2, MVWB855DC3, MVWB855DC4
- Appliance
- Top-load washer
- Platform
- Top-load washer platform, documentation from about 2017
- Models on this platform
- 24 across Maytag, Whirlpool
- Documented fault codes
- 35 with explanations
- Service diagnostic mode
- Yes — a console-only test mode used by technicians to read stored codes and run component tests
- Service documentation
- Tech sheet, service manual (used by our technicians; not published)
Maytag MVWB855DC error codes
These are the fault codes documented for the platform this model belongs to. A code describes a condition the control detected; it does not by itself identify a failed part. Select a code for causes, safe checks and repair context.
| Code | Meaning | Areas involved |
|---|---|---|
| F0E2 | Too many suds | Water-level pressure sensor and hose, Main control board |
| F0E3 | Overload | Gearcase / transmission and basket drive, Drive motor, Main control board |
| F0E4 | Spin limited by water temperature | Water inlet valve, Temperature sensor (thermistor) |
| F0E5 | Off-balance load | Suspension rods, springs and dampers |
| F1E1 | Main control fault | Main control board |
| F1E2 | Motor control fault | Main control board, Drive motor, Wiring harness and connectors |
| F1E3 | Control and console mismatch | Main control board, User interface / keypad board |
| F2E1 | Stuck button | User interface / keypad board |
| F2E3 | Control and console mismatch | Main control board, User interface / keypad board |
| F2E4 | Console software incompatible | User interface / keypad board |
| F2E5 | Console memory corrupt | User interface / keypad board |
| F3E1 | Pressure system fault | Water-level pressure sensor and hose, Main control board, Wiring harness and connectors |
| F3E2 | Inlet water temperature sensor fault | Temperature sensor (thermistor), Wiring harness and connectors, Main control board |
| F3E4 | Bulk dispenser fault | Detergent dispenser, Main control board, Wiring harness and connectors |
| F4E1 | Heater stuck on | Main control board |
| F4E2 | Heater not turning on | Main control board, Wiring harness and connectors |
| F5E1 | Lid switch fault | Lid lock assembly, Main control board, Wiring harness and connectors |
| F5E2 | Lid will not lock | Lid lock assembly, Main control board |
| F5E3 | Lid will not unlock | Lid lock assembly, Main control board |
| F5E4 | Lid not opened between cycles | Lid lock assembly |
| F6E2 | Console not receiving from control | Wiring harness and connectors, Main control board, User interface / keypad board |
| F6E3 | Main control not receiving from console | Wiring harness and connectors, Main control board, User interface / keypad board |
| F7E0 | Loss of power | Main control board, Wiring harness and connectors |
| F7E1 | Power lost during spin | Main control board, Wiring harness and connectors |
| F7E2 | Motor drive overheating | Motor control / inverter board, Drive motor, Main control board |
| F7E3 | Motor drive overcurrent | Motor control / inverter board, Drive motor, Main control board |
| F7E4 | Motor drive overvoltage | Motor control / inverter board, Drive motor, Main control board |
| F7E5 | Shifter fault | Shifter (shift actuator), Wiring harness and connectors, Main control board |
| F7E6 | Motor circuit open | Drive motor, Wiring harness and connectors, Main control board |
| F7E7 | Motor unable to reach target speed | Drive motor, Gearcase / transmission and basket drive, Main control board |
| F7E8 | Motor overheating | Drive motor, Gearcase / transmission and basket drive, Main control board |
| F7E9 | Locked rotor | Drive motor, Gearcase / transmission and basket drive, Main control board |
| F8E3 | Overflow | Water inlet valve, Water-level pressure sensor and hose, Main control board |
| F8E6 | Water hazard (water with lid open) | Water-level pressure sensor and hose, Water inlet valve, Lid lock assembly |
| F9E2 | Unable to drain water from load | Drain pump, Water-level pressure sensor and hose, Main control board |
Common washer problems
- Not draining
Documented check order on this platform: Drain hose installation → Drain pump and pump inlet → Wiring and connectors → Main control board - Not spinning
Documented check order on this platform: Lid or door switch / lock → Wiring and connectors → Drive or pump motor → Main control board - Not filling
Documented check order on this platform: Inlet hose screens → Drain hose installation → Water inlet valve → Main control board - Not agitating
Documented check order on this platform: Lid or door switch / lock → Wiring and connectors → Drive or pump motor → Main control board - Leaking
Documented check order on this platform: Water-level pressure sensing → Water inlet valve → Main control board - Not starting
Documented check order on this platform: Power supply to the appliance → Wiring and connectors → User interface / keypad → Main control board → Lid or door switch / lock - Shaking or noisy
- Door or lid locked
- Stops mid-cycle
- Bad odor
Typical washer repair costs
| Repair | Typical range | Labor |
|---|---|---|
| Washer drain pump replacement | $180–$420 | Moderate |
| Washer water inlet valve replacement | $180–$360 | Light |
| Washer water-level pressure sensor repair | $180–$350 | Light |
| Top-load washer lid lock replacement | $180–$370 | Light |
| Washer drive motor replacement | $300–$720 | Heavy |
| Washer motor control board replacement | $280–$600 | Moderate |
| Top-load washer shifter replacement | $220–$460 | Moderate |
| Top-load washer gearcase / transmission replacement | $400–$880 | Major |
| Washer drive belt replacement | $180–$330 | Light |
| Washer suspension rods, springs or dampers replacement | $180–$440 | Moderate |
Typical total ranges for the Las Vegas area, parts and labor included. The final cost depends on diagnosis, the exact model, parts availability and whether other damage is found.
Repair or replace?
Washers typically last about 10–13 years. Service documentation for this platform dates from about 2017, so the oldest units built on it are now around 9 years old. The age printed in the serial number, the repair cost and the condition of the rest of the appliance decide it. Use the repair-or-replace guide.
Models built on the same platform
These models share this platform's service documentation, so fault codes and most diagnostic steps are the same.
- Whirlpool WTW7000DW
- Whirlpool WTW7040DW
- Whirlpool WTW7300DC
- Whirlpool WTW7300DW
- Whirlpool WTW8000DW
- Whirlpool WTW8040DW
- Whirlpool WTW8500DC
- Whirlpool WTW8500DR
- Whirlpool WTW8500DW
- Whirlpool WTW8510FC
- Whirlpool WTW8510FW
- Maytag MVWB755DW
- Maytag MVWB757JW
- Maytag MVWB765FC
- Maytag MVWB765FW
- Maytag MVWB766FW
- Maytag MVWB835DC
- Maytag MVWB835DW
- Maytag MVWB855DW
- Maytag MVWB865FC
- Maytag MVWB865FW
- Maytag MVWB865GC
- Maytag MVWB865GW
Need your Maytag MVWB855DC repaired in the Las Vegas area?
We repair Whirlpool, Maytag, KitchenAid, JennAir, Amana and other Whirlpool-family appliances in Las Vegas, Henderson, Summerlin and Boulder City. A model number helps but is never required to book.