Model support
Maytag MTW7205RR Top-load washer
Troubleshooting, fault codes and repair information for the Maytag MTW7205RR, organized around the engineering platform this top-load washer is built on.
- Brand
- Maytag
- Model
- MTW7205RR
- Engineering revisions
- MTW7205RR0, MTW7205RR1
- Appliance
- Top-load washer
- Platform
- Top-load washer platform, documentation from about 2025
- Models on this platform
- 13 across Maytag
- Documented fault codes
- 33 with explanations
- Service diagnostic mode
- Yes — a console-only test mode used by technicians to read stored codes and run component tests
- Service documentation
- Tech sheet, service manual (used by our technicians; not published)
Maytag MTW7205RR error codes
These are the fault codes documented for the platform this model belongs to. A code describes a condition the control detected; it does not by itself identify a failed part. Select a code for causes, safe checks and repair context.
| Code | Meaning | Areas involved |
|---|---|---|
| F0E2 | Too many suds | Water-level pressure sensor and hose, Main control board |
| F0E3 | Overload | Gearcase / transmission and basket drive, Drive motor, Main control board |
| F0E5 | Off-balance load | Suspension rods, springs and dampers |
| F0E6 | Motion sensor orientation | Wiring harness and connectors |
| F0E7 | Load detected during Clean Washer cycle | Gearcase / transmission and basket drive |
| F0E8 | Too much leftover water | Drain pump, Water-level pressure sensor and hose |
| F0E9 | Off-balance pause | Suspension rods, springs and dampers |
| F1E1 | Main control fault | Main control board |
| F1E2 | Motor drive voltage fault | Motor control / inverter board, Drive motor, Main control board |
| F1E3 | Motion sensor not responding | Wiring harness and connectors, Main control board |
| F2E1 | Stuck button | User interface / keypad board |
| F2E2 | Console disconnected | User interface / keypad board, Wiring harness and connectors, Main control board |
| F3E2 | Pressure system fault | Water-level pressure sensor and hose, Main control board |
| F3E2-1 | Pressure sensor reading out of range | Water-level pressure sensor and hose, Main control board |
| F3E5 | Bulk detergent system error | Detergent dispenser |
| F5E1 | Lid switch fault | Lid lock assembly, Main control board, Wiring harness and connectors |
| F5E3 | Lid will not unlock | Lid lock assembly, Main control board |
| F5E4 | Lid not opened between cycles | Lid lock assembly |
| F6E1 | Console and control not communicating | Wiring harness and connectors, Main control board, User interface / keypad board |
| F6E2 | Main control not receiving from motor control | Motor control / inverter board, Main control board, Wiring harness and connectors |
| F6E3 | Main control not receiving from motion sensor | Wiring harness and connectors, Main control board |
| F7E2 | Motor drive failure | Motor control / inverter board, Drive motor, Main control board |
| F7E3 | Basket engaged during wash | Shifter (shift actuator), Agitator or wash plate, Wiring harness and connectors |
| F7E4 | Basket re-engagement failure | Shifter (shift actuator), Agitator or wash plate, Wiring harness and connectors |
| F7E7 | Motor unable to reach target speed | Drive motor, Gearcase / transmission and basket drive, Main control board |
| F7E8 | Motor drive overheating | Motor control / inverter board, Drive motor, Wiring harness and connectors |
| F7E9 | Locked rotor | Drive motor, Gearcase / transmission and basket drive, Main control board |
| F7EA | Motor phase lost | Drive motor, Wiring harness and connectors, Main control board |
| F8E1 | No fill or long fill | Water inlet valve, Water-level pressure sensor and hose, Main control board |
| F8E3 | Overflow | Water inlet valve, Water-level pressure sensor and hose, Main control board |
| F8E6 | Water hazard (water with lid open) | Water-level pressure sensor and hose, Water inlet valve, Lid lock assembly |
| F9E1 | Long drain | Drain pump, Water-level pressure sensor and hose, Main control board |
| F9E2-5 | Drain pump disconnected | Drain pump, Wiring harness and connectors |
Common washer problems
- Not draining
- Not spinning
- Not filling
- Not agitating
- Leaking
- Not starting
- Shaking or noisy
- Door or lid locked
- Stops mid-cycle
- Bad odor
Typical washer repair costs
| Repair | Typical range | Labor |
|---|---|---|
| Washer drain pump replacement | $180–$420 | Moderate |
| Washer water inlet valve replacement | $180–$360 | Light |
| Washer water-level pressure sensor repair | $180–$350 | Light |
| Top-load washer lid lock replacement | $180–$370 | Light |
| Washer drive motor replacement | $300–$720 | Heavy |
| Washer motor control board replacement | $280–$600 | Moderate |
| Top-load washer shifter replacement | $220–$460 | Moderate |
| Top-load washer gearcase / transmission replacement | $400–$880 | Major |
| Washer drive belt replacement | $180–$330 | Light |
| Washer suspension rods, springs or dampers replacement | $180–$440 | Moderate |
Typical total ranges for the Las Vegas area, parts and labor included. The final cost depends on diagnosis, the exact model, parts availability and whether other damage is found.
Repair or replace?
Washers typically last about 10–13 years. The age printed in the serial number, the repair cost and the condition of the rest of the appliance decide it. Use the repair-or-replace guide.
Models built on the same platform
These models share this platform's service documentation, so fault codes and most diagnostic steps are the same.
- Maytag MTW6200RF
- Maytag MTW6200RR
- Maytag MTW6200RW
- Maytag MTW6205RF
- Maytag MTW6205RR
- Maytag MTW6205RW
- Maytag MTW7200RF
- Maytag MTW7200RR
- Maytag MTW7200RW
- Maytag MTW7205RF
- Maytag MTW7205RW
- Maytag MTW7405RR
Need your Maytag MTW7205RR repaired in the Las Vegas area?
We repair Whirlpool, Maytag, KitchenAid, JennAir, Amana and other Whirlpool-family appliances in Las Vegas, Henderson, Summerlin and Boulder City. A model number helps but is never required to book.