Washer error codes
Washer fault codes documented for Whirlpool-family brands. Where one code has more than one meaning, each is listed with the appliance type it applies to.
| Code | Meaning | Appliance | Brand pages |
|---|---|---|---|
| F0E1 | Load detected during Clean Washer cycle F0E1 means the washer sensed clothes or other weight in the drum while running the Clean Washer (tub cleaning) cycle, which must run empty. | Front-load washer | Whirlpool, Maytag |
| F0E2 | Oversuds F0E2 means the washer detected too much suds in the tub and could not clear it with its own rinse-and-flush routine. | Front-load washer | Whirlpool, Maytag, Amana, Inglis |
| F0E2 | Too many suds F0E2 means the washer detected too much suds in the tub, either because suds kept the basket from reaching spin speed or because the water-level sensor saw the foam… | Top-load washer | Whirlpool, Maytag, Amana, Roper, Admiral, Crosley |
| F0E3 | Over load F0E3 means the washer judged the drum to be too full for the selected cycle. | Front-load washer | Whirlpool, Maytag |
| F0E3 | Overload F0E3 means the control judged the load to be larger than the washer can handle, or found that the basket could not be turned when it tried to move it. | Top-load washer | Whirlpool, Maytag, Amana, Crosley, Inglis |
| F0E4 | High water temperature F0E4 means the washer measured wash water hotter than the cycle allows. | Front-load washer | Whirlpool, Maytag, Amana, Inglis |
| F0E4 | Spin speed limited by water temperature F0E4 means the washer reduced its spin speed because the water or load was hotter than it allows for full-speed spinning. | Front-load washer | Whirlpool, Maytag |
| F0E4 | Rinse water too hot F0E4 means the washer measured warm water during a rinse, when it expects cold, so hot water is reaching the tub when it should not. | Top-load washer | Whirlpool, Maytag, Amana, Roper, Admiral, Crosley |
| F0E4 | Spin limited by water temperature F0E4 means the water in the tub was too hot for a full-speed spin, so the washer limited spin speed for that cycle to protect the load and the machine. | Top-load washer | Whirlpool, Maytag, Crosley |
| F0E5 | Off-balance load F0E5 means the washer could not balance the load well enough to spin at full speed. | Front-load washer | Whirlpool, Maytag, Amana, Inglis |
| F0E5 | Off-balance load F0E5 means the washer detected that the load was unevenly distributed in the basket and could not spin it safely. | Top-load washer | Whirlpool, Maytag, Amana, Roper, Admiral, Crosley |
| F0E6 | Displacement sensor not detected F0E6 means the main control does not detect the displacement measurement sensor (DMS) it expects to find. | Front-load washer | Whirlpool, Maytag |
| F0E6 | Motion sensor orientation F0E6 means the motion sensor mounted on the tub reported that it is not level, so the control cannot trust its vibration readings. | Top-load washer | Maytag |
| F0E7 | Clothes detected during Clean Washer cycle F0E7 means the washer detected clothes in the drum during the Clean Washer cycle, which has to run with the drum empty. | Front-load washer | Whirlpool, Maytag |
| F0E7 | Load detected during Clean Washer cycle F0E7 means the washer sensed laundry in the basket after the Clean Washer cycle was selected, so it stopped. | Top-load washer | Whirlpool, Maytag |
| F0E8 | Too much leftover water F0E8 means the washer found more water left in the tub than it expects at that point in the cycle. | Top-load washer | Whirlpool, Maytag |
| F0E9 | Off-balance pause F0E9 means the washer kept detecting an off-balance load even after its own attempts (and yours) to fix it, so it paused the cycle. | Top-load washer | Whirlpool, Maytag |
| F1E1 | Main control fault F1E1 means the main control's own self-check found an internal problem, such as corrupted memory or a fault in its power or relay circuits. | Front-load washer | Whirlpool, Maytag, Amana, Crosley, Inglis |
| F1E1 | Main control fault F1E1 means the main control board detected a problem with its own operation. | Top-load washer | Whirlpool, Maytag, Amana, Roper, Admiral, Crosley |
| F1E2 | Motor control fault F1E2 means the part of the electronics that drives the motor reported a fault, such as supply power out of range, excess current or an internal malfunction. | Front-load washer | Whirlpool, Maytag, Amana, Inglis |
| F1E2 | Motor control fault F1E2 means the main control found a fault in its own motor-control section, the part of the board that drives the washer motor. | Top-load washer | Whirlpool, Maytag, Amana, Roper, Admiral, Crosley |
| F1E2 | Motor drive voltage fault F1E2 means the main control saw the internal supply voltage of the motor drive go outside its allowed range. | Top-load washer | Whirlpool, Maytag |
| F1E3 | Displacement sensor fault F1E3 means the displacement measurement sensor (DMS) is connected but the main control considers its signal faulty. | Front-load washer | Whirlpool, Maytag |
| F1E3 | Control and console mismatch F1E3 means the identity reported by the console (user interface) board does not match what the main control expects for this model. | Top-load washer | Whirlpool, Maytag, Amana, Crosley, Inglis |
| F1E3 | Motion sensor not responding F1E3 means the motion sensor (accelerometer) on the tub stopped responding to the main control. | Top-load washer | Maytag |
| F1E6 | Supply overvoltage F1E6 means the washer's control measured the household supply above the range it is designed to accept. | Front-load washer | Whirlpool, Maytag |
| F1E7 | Wrong supply frequency F1E7 means the control detected a household power frequency different from what the washer is built for. | Front-load washer | Whirlpool, Maytag |
| F2E1 | Stuck key F2E1 means the control sees a console button as pressed for much longer than a normal press. | Front-load washer | Whirlpool, Maytag |
| F2E1 | Stuck button F2E1 means the console reports a button that stays pressed far longer than anyone would hold it. | Top-load washer | Whirlpool, Maytag, Amana, Roper, Admiral, Crosley |
| F2E2 | Keypad or display disconnected F2E2 means the main control lost its connection to the keypad or display board. | Front-load washer | Whirlpool, Maytag |
| F2E2 | Console disconnected F2E2 means the main control lost its connection to the console (display and buttons). | Top-load washer | Whirlpool, Maytag |
| F2E3 | Unsupported cycle F2E3 means the control was asked to run a cycle it does not recognize for this model, which points at corrupted cycle data or a board that does not match the washer. | Front-load washer | Whirlpool, Maytag |
| F2E3 | Control and console mismatch F2E3 means the main control and the console board do not match each other for this model. | Front-load washer | Whirlpool, Maytag |
| F2E3 | Control and console mismatch F2E3 means the main control and the console (user interface) board do not identify as a matching pair for this model. | Top-load washer | Whirlpool, Maytag, Amana, Roper, Admiral, Crosley |
| F2E3 | Console switch mismatch F2E3 means the switches the control reads on the console do not match the console it expects, or are not working correctly. | Top-load washer | Whirlpool, Maytag, Amana, Roper, Admiral, Crosley |
| F2E4 | Console software incompatible F2E4 means the configuration file stored in the console (user interface) board is not the correct one for this washer. | Top-load washer | Whirlpool, Maytag, Amana, Crosley, Inglis |
| F2E5 | Console memory corrupt F2E5 means the configuration data stored in the console (user interface) board is corrupt. | Top-load washer | Whirlpool, Maytag, Amana, Crosley, Inglis |
| F3E1 | Water level sensor fault F3E1 means the main control received a water-level (pressure) signal outside the range it considers possible, so it cannot trust the level reading. | Front-load washer | Whirlpool, Maytag, Amana, Crosley, Inglis |
| F3E1 | Steam temperature sensor F3E1 on this platform means the control has a problem reading the steam temperature sensor. | Front-load washer | Whirlpool, Maytag |
| F3E1 | Pressure system fault F3E1 means the main control received a water-level (pressure) signal that is outside the range it considers possible, so it cannot trust how much water is in the tub. | Top-load washer | Whirlpool, Maytag, Amana, Roper, Admiral, Crosley |
| F3E2 | Water temperature sensor fault F3E2 means the reading from the wash water temperature sensor is open, shorted or outside its believable range. | Front-load washer | Whirlpool, Maytag, Amana, Crosley, Inglis |
| F3E2 | Pressure sensor fault F3E2 on this platform means the control has a problem with the water level (pressure) sensor or switch. | Front-load washer | Whirlpool, Maytag |
| F3E2 | Inlet water temperature sensor fault F3E2 means the sensor that measures incoming water temperature is giving a reading that indicates an open or shorted circuit. | Top-load washer | Whirlpool, Maytag, Amana, Roper, Admiral, Crosley |
| F3E2 | Pressure system fault F3E2 means the main control received a water-level (pressure) signal that is missing or outside the range it considers possible. | Top-load washer | Whirlpool, Maytag, Crosley |
| F3E2-1 | Pressure sensor reading out of range F3E2-1 means the water-level pressure sensor is reporting a reading outside its valid range. | Top-load washer | Maytag |
| F3E3 | Inlet water temperature sensor F3E3 means the control has a problem reading the sensor that measures incoming water temperature. | Front-load washer | Whirlpool, Maytag |
| F3E3 | Inlet water temperature sensor fault F3E3 means the sensor that measures incoming water temperature reads as an open or shorted circuit. | Top-load washer | Whirlpool, Maytag |
| F3E4 | Motor temperature sensor F3E4 means the control has a problem reading the motor temperature sensor. | Front-load washer | Whirlpool, Maytag |
| F3E4 | Bulk dispenser fault F3E4 means the main control cannot detect the expansion board that runs the bulk (multi-load) detergent dispenser. | Top-load washer | Whirlpool, Maytag |
| F3E5 | Dry temperature sensor fault F3E5 means the temperature sensor used by the drying or air-flow feature reads open, shorted or out of range. | Front-load washer | Whirlpool, Maytag |
| F3E5 | Bulk detergent system error F3E5 means the level sensor in the bulk detergent reservoir is giving a reading outside its valid range. | Top-load washer | Whirlpool, Maytag |
| F3E6 | Accelerometer fault F3E6 means the motion sensor (accelerometer) on the main control failed its self-test or reported an impossible orientation. | Front-load washer | Whirlpool, Maytag |
| F3E6 | Rotor position sensor F3E6 on this platform means the control has a problem with the sensor that reports the motor rotor position. | Front-load washer | Whirlpool, Maytag |
| F3E7 | Wash temperature sensor F3E7 means the control has a problem reading the wash water temperature sensor. | Front-load washer | Whirlpool, Maytag |
| F3E8 | Dry temperature sensor F3E8 means the control has a problem reading the temperature sensor used by the drying function, on models that have one. | Front-load washer | Whirlpool, Maytag |
| F4E1 | Wash heater fault F4E1 means the washer switched on its wash heater but the control did not see the water temperature rise as expected. | Front-load washer | Whirlpool, Maytag, Amana, Inglis |
| F4E1 | Steam heater F4E1 on this platform means the control detected a problem with the steam heater. | Front-load washer | Whirlpool, Maytag |
| F4E1 | Heater stuck on F4E1 means the control detected that the water heater was on at a time it should have been off. | Top-load washer | Whirlpool, Maytag, Amana, Crosley, Inglis |
| F4E2 | Wash heater not turning on F4E2 means the control commanded the wash heater on, but its check shows the heater circuit did not switch on. | Front-load washer | Whirlpool, Amana, Inglis |
| F4E2 | Heating timeout F4E2 on this platform means the water did not reach the target temperature within the time the control allows for heating. | Front-load washer | Maytag |
| F4E2 | Main heater stuck on F4E2 on this platform means the control detected the main heater staying on when it should be off. | Front-load washer | Whirlpool, Maytag |
| F4E2 | Heater not turning on F4E2 means the control switched the water heater on but could not detect that it was actually heating. | Top-load washer | Whirlpool, Maytag, Amana, Crosley, Inglis |
| F4E3 | Main heater not turning on F4E3 means the control commanded the main heater on, but the heater did not turn on. | Front-load washer | Whirlpool, Maytag |
| F4E4 | Vent fan or dry blower fault F4E4 means the control found an open or shorted circuit at the fan it uses after or during the cycle: a vent fan on some washers, a drying blower on combination… | Front-load washer | Whirlpool, Maytag |
| F4E4 | Main heater grounded F4E4 on this platform means the control detected that the main heater circuit has a path to ground (electrical leakage). | Front-load washer | Whirlpool, Maytag |
| F5E1 | Door switch fault F5E1 means the control saw the door switch open while the door was supposed to be locked. | Front-load washer | Whirlpool, Maytag, Amana, Crosley, Inglis |
| F5E1 | Lid switch fault F5E1 means the control expected the lid to be closed and locked, but its lid switch reads open. | Top-load washer | Whirlpool, Maytag, Amana, Roper, Admiral, Crosley |
| F5E2 | Door will not lock F5E2 means the washer tried to lock the door at the start of the cycle and could not confirm that it locked. | Front-load washer | Whirlpool, Maytag, Amana, Crosley, Inglis |
| F5E2 | Lid will not lock F5E2 means the washer tried to lock the lid but could not confirm the lock reached its locked position. | Top-load washer | Whirlpool, Maytag, Amana, Roper, Admiral, Crosley |
| F5E3 | Door will not unlock F5E3 means the washer tried to unlock the door and could not confirm that it unlocked, so the door may stay locked. | Front-load washer | Whirlpool, Maytag, Amana, Crosley, Inglis |
| F5E3 | Lid will not unlock F5E3 means the washer tried to release the lid lock but could not confirm it reached the unlocked position. | Top-load washer | Whirlpool, Maytag, Amana, Roper, Admiral, Crosley |
| F5E4 | Door not opened between cycles F5E4 means the washer was started several times in a row without the door being opened, or the control cannot see the door switch change between cycles. | Front-load washer | Whirlpool, Maytag, Amana, Inglis |
| F5E4 | Lid not opened between cycles F5E4 means Start was pressed after several cycles in a row without the lid being opened, so the washer asks you to open and close it. | Top-load washer | Whirlpool, Maytag, Amana, Roper, Admiral, Crosley |
| F6E1 | Main control to motor control communication F6E1 on these platforms means the main control is not hearing from the motor control unit. | Front-load washer | Whirlpool, Maytag |
| F6E1 | Main control cannot hear console F6E1 on these platforms means the main control is not receiving messages from the console (user interface) board. | Front-load washer | Whirlpool, Maytag |
| F6E1 | Console and control not communicating F6E1 means the console and the main control stopped exchanging data. | Top-load washer | Whirlpool, Maytag |
| F6E2 | Console and main control communication F6E2 on these platforms means the console (user interface) and the main control are not communicating. | Front-load washer | Whirlpool, Maytag, Amana, Crosley, Inglis |
| F6E2 | Main control cannot hear motor control F6E2 on this platform means the main control is not receiving messages from the motor control. | Front-load washer | Whirlpool, Maytag |
| F6E2 | Console not receiving from control F6E2 means the console (user interface) is not receiving data from the main control. | Top-load washer | Whirlpool, Maytag, Amana, Crosley, Inglis |
| F6E2 | Main control not receiving from motor control F6E2 means the main control is not receiving data from the motor control unit. | Top-load washer | Maytag |
| F6E3 | Main control and console communication F6E3 on these older platforms means the main control and the console (user interface) are not communicating. | Front-load washer | Whirlpool, Maytag, Amana, Crosley |
| F6E3 | Main control to motor control communication F6E3 on these platforms means the main control is not receiving messages from the motor controller. | Front-load washer | Whirlpool, Maytag, Amana, Inglis |
| F6E3 | Main control to displacement sensor communication F6E3 on this platform means the main control is not communicating with the displacement measurement sensor (DMS). | Front-load washer | Whirlpool, Maytag |
| F6E3 | Main control not receiving from console F6E3 means the main control is not receiving data from the console (user interface). | Top-load washer | Whirlpool, Maytag, Amana, Crosley, Inglis |
| F6E3 | Main control not receiving from motor control F6E3 means the main control is not receiving data from the motor control unit that runs the washer motor. | Top-load washer | Whirlpool, Maytag |
| F6E3 | Main control not receiving from motion sensor F6E3 means the main control is not receiving data from the motion sensor mounted on the tub. | Top-load washer | Maytag |
| F7E0 | Loss of power F7E0 means the main control saw its supply voltage drop too low or disappear. | Top-load washer | Whirlpool, Maytag, Amana, Crosley, Inglis |
| F7E1 | Drive motor tachometer error F7E1 on these platforms means the control is not getting a usable speed signal from the drive motor. | Front-load washer | Whirlpool, Maytag, Amana, Crosley |
| F7E1 | Basket speed sensing fault F7E1 means the main control could not read how fast the basket or motor is turning, or the speed reading changed faster than is physically possible. | Top-load washer | Whirlpool, Maytag, Amana, Roper, Admiral, Crosley |
| F7E1 | Power lost during spin F7E1 means power was interrupted while the basket was spinning, so the washer waits a few minutes for the basket to stop before it continues. | Top-load washer | Whirlpool, Maytag |
| F7E2 | Motor control overheat or internal fault F7E2 means the motor control reported a problem with itself: its drive electronics overheated, drew too much current or detected an internal failure, depending on the… | Front-load washer | Whirlpool, Maytag, Amana, Crosley, Inglis |
| F7E2 | Motor drive overheating F7E2 means the main control detected a problem in the motor drive, reported on these models as the drive overheating. | Top-load washer | Whirlpool, Maytag |
| F7E2 | Motor drive failure F7E2 means the main control detected a failure in the motor drive hardware or in the motor it runs. | Top-load washer | Whirlpool, Maytag, Amana, Crosley, Inglis |
| F7E3 | Motor drive overcurrent F7E3 means the main control detected excessive current in the motor drive. | Top-load washer | Whirlpool, Maytag |
| F7E3 | Basket engaged during wash F7E3 means the basket stayed coupled to the drive during the wash phase, when only the wash plate or agitator should be moving. | Top-load washer | Whirlpool, Maytag, Amana, Crosley, Inglis |
| F7E4 | Motor drive overvoltage F7E4 means the main control detected that the motor drive's internal voltage went above its limit. | Top-load washer | Whirlpool, Maytag |
| F7E4 | Basket re-engagement failure F7E4 means the shifter did not re-engage the basket for spin after a wash phase. | Top-load washer | Whirlpool, Maytag, Amana, Crosley, Inglis |
| F7E5 | Shifter fault F7E5 means the main control could not confirm the position of the shifter, the part that switches the drive between wash and spin. | Top-load washer | Whirlpool, Maytag, Amana, Roper, Admiral, Crosley |
| F7E6 | Motor circuit open F7E6 means the main control found an open circuit in one or more of the motor's windings or supply lines. | Top-load washer | Whirlpool, Maytag, Amana, Roper, Admiral, Crosley |
| F7E7 | Motor unable to reach target speed F7E7 means the motor was running but the basket did not reach the speed the control commanded. | Top-load washer | Whirlpool, Maytag, Amana, Roper, Admiral, Crosley |
| F7E8 | Motor over temperature F7E8 means the drive motor got too hot, so the control stopped it until it cools. | Front-load washer | Whirlpool, Maytag, Amana, Inglis |
| F7E8 | Motor overheating F7E8 means the main control determined that the motor temperature was too high and stopped it. | Top-load washer | Whirlpool, Maytag, Amana, Crosley, Inglis |
| F7E8 | Motor drive overheating F7E8 means the main control detected a problem in the motor drive, reported as the drive overheating. | Top-load washer | Whirlpool, Maytag |
| F7E9 | Motor locked rotor F7E9 means the motor was powered but did not turn (a locked rotor). | Front-load washer | Whirlpool, Maytag, Amana, Inglis |
| F7E9 | Locked rotor F7E9 means the control was driving the motor but the motor was not turning. | Top-load washer | Whirlpool, Maytag, Amana, Crosley, Inglis |
| F7EA | Motor lost phase F7EA means the motor control detected that one of the motor's power phases is missing. | Front-load washer | Whirlpool, Maytag |
| F7EA | Motor phase lost F7EA means one or more of the motor's three power phases was lost or carried less current than expected. | Top-load washer | Whirlpool, Maytag |
| F7EC | Motor overload F7EC means the motor control detected the motor working beyond its load limit. | Front-load washer | Whirlpool, Maytag |
| F7E10 | Motor disconnected F7E10 means the control sees the drive motor as disconnected. | Front-load washer | Whirlpool, Maytag |
| F7E12 | Motor control overload F7E12 means the motor control detected an overload on the motor drive. | Front-load washer | Whirlpool, Maytag |
| F8E0 | Steam inlet valve error F8E0 means the control detected a problem with the water valve that feeds the steam feature, on models that have steam. | Front-load washer | Whirlpool, Maytag |
| F8E1 | Long fill / no fill F8E1 means the washer has been filling longer than it allows without seeing the water level rise enough. | Front-load washer | Whirlpool, Maytag, Amana, Crosley, Inglis |
| F8E1 | No fill or long fill F8E1 means the washer was filling but the control did not see the water level rise within the time it allows. | Top-load washer | Whirlpool, Maytag, Amana, Roper, Admiral, Crosley |
| F8E2 | Dispenser system error F8E2 means the dispenser motor could not reach, or confirm, the position needed to dispense detergent or additives. | Front-load washer | Whirlpool, Maytag |
| F8E2 | Dispenser pump fault F8E2 means the bulk detergent pump was switched on but its electrical current was outside the expected range. | Top-load washer | Whirlpool, Maytag |
| F8E3 | Overflow F8E3 means the control detected more water or foam in the tub than it should ever hold, and is draining to prevent a flood. | Front-load washer | Whirlpool, Maytag, Amana, Crosley, Inglis |
| F8E3 | Overflow F8E3 means the control sensed a water level higher than the washer's capacity. | Top-load washer | Whirlpool, Maytag, Amana, Roper, Admiral, Crosley |
| F8E4 | Flow meter fault F8E4 means that during the service quick test, the flow meter measured almost no water entering the washer. | Front-load washer | Whirlpool, Maytag |
| F8E5 | Hot and cold supply reversed F8E5 means the washer detected that the hot and cold water hoses are connected to the wrong inlets. | Front-load washer | Whirlpool, Maytag |
| F8E5 | Hot and cold reversed F8E5 means the washer detected hot water when it opened the cold side (or the reverse), so the fill hoses appear to be swapped. | Top-load washer | Whirlpool, Maytag, Amana, Roper, Admiral, Crosley |
| F8E6 | Water hazard (water with lid open) F8E6 means the washer detected water in the tub while the lid had been left open for an extended time. | Top-load washer | Whirlpool, Maytag, Amana, Crosley, Inglis |
| F8E6 | No fill F8E6 means the washer was filling but the control did not see the water level rise within the time it allows. | Top-load washer | Maytag |
| F9E1 | Long drain F9E1 means the drain pump ran, but the control did not see the water level fall within the time it allows for draining. | Front-load washer | Whirlpool, Maytag, Amana, Crosley, Inglis |
| F9E1 | Long drain F9E1 means the washer switched on its drain pump, but the control did not see the water level drop within the time it allows for draining. | Top-load washer | Whirlpool, Maytag, Amana, Roper, Admiral, Crosley |
| F9E2 | Unable to drain water from load F9E2 means the washer could not remove the water held in the load, indicating a problem in the drain system. | Top-load washer | Whirlpool, Maytag |
| F9E2-5 | Drain pump disconnected F9E2-5 means the main control detected no electrical connection to the drain pump. | Top-load washer | Maytag |
| F1 | Primary control failure F1 (F, then 1) means the washer's machine/motor control reported a failure. A later revision of the documentation for these models ties the code to the water-level… | Top-load washer | Whirlpool, Maytag |
| F1 | Pressure signal out of range F1 (F, then 1) means the control received a water-level pressure signal outside its valid range. | Top-load washer | Whirlpool, Maytag |
| F2 | Keypad or console failure F2 (F, then 2) means the control found a problem with the keypad or console: a stuck key during diagnostics, or a console fault or mismatch in standby. | Top-load washer | Whirlpool, Maytag |
| F40 | Water temperature sensor open or shorted F40 (F, then 40) means the water temperature sensor used for automatic temperature control reads as an open or shorted circuit. | Top-load washer | Whirlpool, Maytag |
| F41 | Motor sensor thermistor open or shorted F41 (F, then 41) means the temperature sensor in the motor's rotor position sensor reads as an open or shorted circuit. | Top-load washer | Whirlpool, Maytag |
| F42 | Heater state unknown F42 (F, then 42) means the control could not tell whether the water heater was on or off. | Top-load washer | Whirlpool, Maytag |
| F43 | Heater stuck on F43 (F, then 43) means the water heater was on when the control had it switched off. | Top-load washer | Whirlpool, Maytag |
| F44 | Heater will not turn on F44 (F, then 44) means the control switched the water heater on but could not detect that it was heating. | Top-load washer | Whirlpool, Maytag |
| F50 | Motor stalled F50 (F, then 50) means the motor's rotor position sensor detected no rotation when the motor should have been turning. | Top-load washer | Whirlpool, Maytag |
| F51 | Motor position sensor failure F51 (F, then 51) means the motor's rotor position sensor failed or its lower wiring harness has a problem. | Top-load washer | Whirlpool, Maytag |
| F52 | Motor did not stop F52 (F, then 52) means the motor's position sensor still detected rotation after the control commanded the motor to stop. | Top-load washer | Whirlpool, Maytag |
| F53 | Motor control overheating F53 (F, then 53) means the machine/motor control detected high temperature in its motor module. | Top-load washer | Whirlpool, Maytag |
| F54 | Motor control overcurrent F54 (F, then 54) means the machine/motor control detected excessive current in its motor module. | Top-load washer | Whirlpool, Maytag |
| F72 | Basket re-engagement failure F72 (F, then 72) means the washer could not confirm that the basket re-engaged with the drive after being released for washing. | Top-load washer | Whirlpool, Maytag |
| HC | Hot and cold reversed HC means the washer detected that the hot and cold fill hoses appear to be connected backwards. | Top-load washer | Whirlpool, Maytag |
| LF | Long fill LF means the washer was filling but the control did not see the water level change within the time it allows. | Top-load washer | Whirlpool, Maytag |
| Ld | Long drain Ld means the drain pump was running but the control did not see the water level drop. | Top-load washer | Whirlpool, Maytag |
| Po | Pump out (lid left open) Po means the lid was left open with water in the tub for an extended time, so the washer is pumping the water out. | Top-load washer | Whirlpool, Maytag |
| Sd | Suds detected Sd means the control sensed suds dragging on the basket. It shows steadily while the washer tries to clear them and flashes if that attempt fails. | Top-load washer | Whirlpool, Maytag |
| dL | Lid lock failure dL means the washer tried to lock the lid but could not confirm the lock reached the locked position. | Top-load washer | Whirlpool, Maytag |
| dU | Lid unlock failure dU means the washer tried to release the lid lock but could not confirm it unlocked. | Top-load washer | Whirlpool, Maytag |
| oL | Overloaded oL means the control judged the load to be larger than the washer can handle, or found that the basket could not release from the drive. | Top-load washer | Whirlpool, Maytag |
| uL | Unbalanced load uL means the washer detected an off-balance load. It shows steadily while the washer tries to rebalance and flashes if that fails. | Top-load washer | Whirlpool, Maytag |